How to Draw a Face on Procreate Step by Step
StyleFrame Team7 min read
To draw a face in Procreate, start with a guide layer: a circle for the cranium, a vertical center line, and horizontal lines for the eyes, nose, and chin. Then sketch the jaw, eye sockets, nose, mouth, and ears on a second layer, lower the guide opacity, and refine into line art. Finish with flat color and shading on separate layers. Working from large shapes to small details, with every stage on its own layer, keeps the drawing easy to correct and easy to animate later.
Set up your canvas and layers
Before you draw anything, set up the file so it can be used in a motion pipeline.
- Canvas size: Pick a canvas that matches your delivery format. For a character that will be animated in After Effects, a 3840×2160 canvas, or a square canvas at a similar pixel dimension, gives you room to scale and crop without softening lines.
- Color profile: If your comp is in a specific working space, note it now so you aren't surprised by color shifts on import.
- Layers: Create at least three: Guides, Sketch, and Line art. Add Color and Shading layers later.
- Brush: Use a plain pencil-style brush for construction (6B or similar) and a clean, slightly weighted inking brush for final lines. Avoid textured brushes for anything you plan to rig, since texture can shimmer when layers move.
You can also turn on a drawing guide from the Actions menu. Keep in mind that real faces aren't perfectly symmetrical, and a mirrored drawing tends to look stiff.
Step 1: Block in the skull and center line
On the Guides layer, draw a circle for the cranium. Don't worry about perfection. Add a vertical line down the middle, then a horizontal line across the circle's center. That horizontal line is your eye line.
Many beginners place the eyes too high. On an average adult head, the eyes sit about halfway between the top of the skull and the chin, which is lower than most people expect. Once you've drawn the circle, extend the vertical center line below it to mark where the chin will land.
Step 2: Divide the face into thirds
Mark three horizontal landmarks:
- Hairline to brow line: the top third.
- Brow line to the base of the nose: the middle third.
- Base of the nose to chin: the bottom third.
Treat these as approximations. Real faces vary, and you'll adjust them for the character you're designing. What matters is that you have consistent landmarks to check against, so a misplaced feature stands out immediately.
Step 3: Shape the jaw and sides of the head
A circle alone makes a head look like a ball. Trim the sides of the circle to create flatter planes, since a real head is narrower side to side than the circle implies.
Then build the jaw:
- Find the ear position. The tops of the ears roughly align with the brow line and the bottoms with the base of the nose.
- Draw the jawline from just below each ear, angling down toward the chin.
- Decide how wide the chin should be. A narrow chin reads as delicate or youthful, a wide one as strong or heavy.
A common mistake is drawing the two sides of the jaw with different curves. Use the Transform tool to check this: duplicate the jaw sketch, flip it horizontally, and compare. Delete the copy once you've corrected any mismatch.
Step 4: Place the eyes
Drop to a new Sketch layer and lower the opacity of the Guides layer.
On the eye line, draw two almond shapes with roughly one eye-width of space between them. The outer corners should land inside the edges of the head with space left for the temples.
Draw the eye socket first as a simple form, then fit the eyeball inside it. Eyelids wrap over a sphere, so the upper lid should curve around the eyeball rather than sit flat on top. Add the brow just above the socket, slightly arched, with the inner end usually lower than the outer end.
Step 5: Draw the nose
The base of the nose sits on your lower guideline. Start with the simplest version:
- A small wedge or soft rectangle for the bridge, running down from between the brows.
- A rounded ball for the tip.
- Two small shapes for the nostril wings on each side.
You don't need to draw the whole nose in line art. Often a soft shadow beside the bridge and a small shape beneath the tip communicate the form. This is easier to judge once you reach the shading stage.
Step 6: Place the mouth
The mouth usually sits about a third of the way between the nose and the chin. Start with a single horizontal line for the mouth's center seam, then add:
- The upper lip, which is typically thinner and sits in shadow.
- The lower lip, which is fuller and catches light.
- The corners, which should end roughly under the pupils for a neutral expression.
The center seam is the most expressive line on the face. Tilt it slightly, curve the corners up or down, and you've changed the whole emotion.
Step 7: Add ears, neck, and hair shape
Ears fit between the brow line and the nose line. Draw a C-shape for the outer rim with a smaller inner curve, and don't over-detail it.
For the neck, use two lines running down from behind the jaw. The neck is thicker than many beginners draw it, and it attaches behind the jawline, not under the chin.
Block in the hair as a mass, not strands. Think about where it sits on the skull, because hair adds volume above the cranium circle you drew in step 1. Define the silhouette first, then add flow lines.
Step 8: Refine into line art
Create a Line art layer above the sketch. Lower the sketch opacity further and trace over it with your inking brush, using confident strokes instead of many short ones.
Vary line weight on purpose: thicker where shapes overlap or sit in shadow, thinner where light hits. If this drawing is going to be animated, separate parts onto individual layers (eyes, brows, mouth, hair, head) now rather than later.
Step 9: Add flat color and shading
Put flat color on a layer beneath the line art. A good habit is to color on one layer per area: skin, hair, eyes, clothing. Then use separate layers above them for shadows and highlights so nothing spills outside the shape.
For shading:
- Pick a single light direction and commit to it.
- Add shadow on the opposite side of the nose, under the brow, under the lower lip, and under the jaw.
- Add a few highlights on the forehead, nose bridge, and lower lip.
- Use a soft brush at low opacity for transitions, and keep hard edges where planes change sharply.
Tinting shadows slightly toward a cool or saturated hue, rather than just darkening the skin color, usually gives richer results.
Drawing a three-quarter view
Once the front view feels comfortable, try a three-quarter turn. The construction is the same, with a few changes:
- The center line curves around the sphere instead of running straight.
- The far eye appears narrower and sits closer to the nose.
- The near side of the face shows more of the cheek, and the far ear is hidden or barely visible.
- The jaw's far edge is foreshortened.
Draw the center line as a curve first, then place features relative to it. Features on the far side of the line compress, and the near side expands.
Common mistakes to avoid
- Eyes placed too high. Check them against the halfway line.
- Skipping construction. Even a rough circle and center line catches most proportion errors.
- Too much detail too soon. Settle the structure before adding lashes, pores, or hair strands.
- Merging everything onto one layer. It limits what you can correct and what you can animate.
- Not flipping the drawing. Flip your drawing horizontally regularly to catch asymmetry you've stopped seeing.
Taking your Procreate face into an animation pipeline
For motion designers and VFX artists, a face drawing is often a starting point, not the final deliverable. Because you kept eyes, brows, mouth, and hair on separate layers, you can bring those layers into your animation software and rig them there. Procreate also includes Animation Assist, a simple animation tool that is useful for quick tests.
Practice routine
Draw ten quick construction heads, a few minutes each, using only the circle, center line, and thirds. Then vary one thing at a time: jaw width, eye spacing, nose length. You'll quickly see how small changes alter character, which is exactly the skill you need for designing faces that read well in motion.