How to Drag to Fill Procreate Pocket Beta
StyleFrame Team8 min read
To drag to fill in Procreate Pocket, including beta builds, press and drag your Active Color swatch from the Colors interface onto the area you want to fill, then release. This is ColorDrop, and the color floods outward until it hits a boundary such as an outline. To control how far it spreads, keep your finger down after dropping, wait for the blue Threshold bar to appear, slide left to fill less or right to fill more, and lift to commit.
What "drag to fill" means in Procreate Pocket
Procreate's fill tool isn't a bucket icon. It's a gesture called ColorDrop. You pick up your current color and drop it onto the canvas, and the app flood-fills the region under your finger.
In Pocket, the Active Color swatch sits in the Colors interface. If you only see the color disc or picker, drag the swipe handle at the top of the panel upward to reveal the Color History, the active palette, and the Active Color. Drag from that swatch onto your artwork.
Fill behavior depends on the layer's contents. ColorDrop spreads from the point where you release until it detects an edge. A clean, closed line drawing gives predictable results. A sketchy, open, or textured outline gives you leaks and gaps.
Step-by-step: fill an area with ColorDrop
- Open the Colors interface and choose your color.
- Drag the swipe handle up if the Active Color swatch isn't visible.
- Press and hold the Active Color swatch, then drag it out onto the canvas.
- Position your finger or Apple Pencil over the region you want to fill.
- Release to fill, or keep holding to adjust the Threshold (below).
If the result looks wrong, undo and try again with a different Threshold or a different reference setup.
Adjust the ColorDrop Threshold
Threshold is the setting that most often decides whether a fill looks right.
- Drag your color over the target area, but don't lift.
- Wait a moment until a thin blue bar appears across the top of the canvas, showing a percentage.
- Without lifting, slide left to reduce the fill or right to increase it.
- Lift to commit.
Procreate remembers the last Threshold you used. If a fill suddenly behaves differently from the one before it, that remembered value is usually why. Check it on every new drop until you've settled on a working value for the piece.
A low Threshold hugs the shape tightly and can leave a thin halo of unfilled pixels along anti-aliased edges. A higher Threshold pushes the fill further into those soft edge pixels and closes the gaps. Too high, and the color spills past the line or covers the whole layer.
Fix: the fill covers the entire canvas
This is the most common complaint in user threads, and it usually comes down to one of three causes.
Threshold is too high. Drop again, hold, and drag left until the fill stays inside the shape. Don't assume it's fine because it isn't at 100%. A value around 50% can still flood a shape.
You're filling an empty layer. If your outline is on one layer and you drop color on a new, empty layer, there's nothing on that layer to stop the flood, so it fills everything. Either fill on the same layer as the line work, or set the line layer as a Reference layer so ColorDrop reads its edges while you fill on the layer beneath.
The line has gaps. Even a tiny break lets the color escape. Close the gap with a brush, or raise the Threshold slightly so the fill treats near-solid edges as boundaries.
Alpha Lock isn't a fix for this. It locks transparent pixels so you can only paint over existing content, which is why enabling it only recolors the outlines rather than filling the shape.
Fix: white specks and unfilled edges
When you fill flat color under line art, you often see small white flecks where the fill stopped short of the line. This commonly happens when the lines come from a textured or semi-opaque brush, since the edge pixels aren't solid enough to read cleanly as part of the boundary.
Options:
- Raise the Threshold a little so the fill pushes into partially transparent edge pixels.
- Redraw key outlines with a solid, fully opaque brush.
- Fill on a layer underneath the line art, with the line layer set as Reference, so any slight overlap hides behind the lines.
For production work where you plan to composite later, filling underneath the line layer is also cleaner, because you keep color and ink separate.
Fill several areas quickly with Continue Filling
On the iPad version, Procreate offers Continue Filling. After a ColorDrop, you tap the Continue Filling option to fill other regions with a simple tap, and you can tap-hold and drag to adjust the Threshold between fills. You exit by tapping the checkmark or switching to another tool. If you're using Pocket, look for the equivalent prompt after your first drop. Because Pocket and iPad don't always share identical interfaces, and betas change, confirm the option is present in your build rather than assuming it.
Other ways to fill if dragging isn't working
Dragging isn't the only route. If ColorDrop misbehaves in your build, these alternatives give you the same result.
- Recolor. A tap-to-fill tool with a Flood slider that controls how aggressively it spreads. On iPad it's reached through the QuickMenu, which you enable under Gesture Controls in Prefs. Check where Pocket exposes it in your version.
- Selection with Color Fill. Make a selection (automatic, freehand, rectangle, or ellipse) with Color Fill toggled on, and the selected area fills as soon as the selection completes. It only works on a single layer, not a group, and the setting persists after you leave Selections, so turn it off when you're done.
- Fill Layer. From the layer options, fill an entire layer with your current color. This is useful for backgrounds and for building a flat base layer to mask or adjust later.
Beta-specific troubleshooting
If you're running a beta build, an odd fill result might be a bug rather than a mistake on your end. A few practical steps help you tell the difference:
- Reproduce it on a fresh canvas. Draw a simple closed shape on a single layer and drop a color inside. If that fails, the problem is likely the build or a setting, not your artwork.
- Check Threshold first. It persists between drops, so a stale high value mimics a bug.
- Test same-layer versus Reference. Fill on the layer that contains the line, then try a separate layer with Reference enabled. This separates layer-logic problems from real regressions.
- Note the version number. Beta behavior can change between builds. Users have reported fill behavior differing between major versions, with a drop applying across the whole canvas regardless of the selected layer.
- Report it. Procreate points testers to its Public Beta feedback board, where developers log issues. Include your device, build number, and the exact steps.
If a beta fill bug blocks you on a deadline, fall back to Selection with Color Fill or Fill Layer and revisit the gesture after the next update.
Why this matters for motion and VFX workflows
Many motion designers use Procreate or Pocket for quick styleframes, storyboards, hand-drawn textures, and rough animation passes, then move the work into After Effects, Premiere Pro, or Nuke. A few habits make that handoff smoother:
- Keep flats on their own layers. Fill under the line art instead of merging, so you can recolor, matte, or relight in the compositor.
- Fill with a reference, not by hand. Reference-based fills give consistent edges across frames, which matters when you're building a short sequence rather than a single illustration.
- Export layers or flat frames at the resolution you need. Check the canvas size before you start, since upscaling later costs detail.
- Name layers clearly. A tidy layer stack saves time when you import files into After Effects or bring them into a 3D scene in Cinema 4D or Blender as textures.
Quick reference
Final notes
ColorDrop is simple once you separate its three variables: the layer it reads, the Threshold you've set, and whether the line art is truly closed. Most "broken" fills trace back to one of those. If a clean test on a fresh canvas still fails in your beta build, document it and report it, and use a selection-based fill until it's fixed.