How to Drag and Fill Color in Procreate
StyleFrame Team7 min read
To drag and fill color in Procreate, touch and drag the Colors icon from the top right of the canvas into a closed area of your artwork, then lift your Apple Pencil or finger to drop the fill. This feature is called ColorDrop. If you keep holding after the color floods in, you can slide left or right to lower or raise the ColorDrop Threshold and control how far the fill spreads. Common causes of "it won't fill" problems include a Threshold that's too high, a Reference layer, or line art with gaps.
How ColorDrop works, step by step
ColorDrop is Procreate's paint bucket, except you drag the color out of the interface instead of picking a bucket tool.
- Pick your color. Open the Colors panel and choose a shade, or tap a swatch from your active palette.
- Select the right layer. Put your fill on a layer beneath or separate from your linework. This keeps your lines editable and makes later changes easy.
- Drag the color dot into the area. Touch the Colors icon in the top right, then sweep in one smooth motion over the shape you want to fill. Don't pause on the dot or tap it first, since that can stop the drag from registering.
- Keep holding. Once the color floods in, don't lift. A blue Threshold bar appears along the top of the canvas with a percentage readout.
- Slide to adjust. Move left to fill less and right to fill more. Procreate remembers the setting after you lift, so the next drop starts from the same value.
- Lift to commit. Releasing the Pencil or finger applies the fill.
If you're filling many shapes, tap Continue Filling after your first drop. You can then tap each region to fill it with the current color, or tap and hold to adjust the Threshold mid-fill. Tap the tick or switch to another tool such as Paint to exit the mode.
On iPads that support Apple Pencil hover, there's a faster route: hover the tip over the current color in the top right and double-tap the side of the Pencil to jump straight into Continue Filling.
Choosing the right Threshold
The Threshold decides how similar neighboring pixels must be to get included in the fill. Think of it as tolerance on a magic wand.
- Low Threshold: The fill stays tight and may leave halos along anti-aliased or soft edges.
- Mid Threshold: A good starting range for clean line art with solid strokes.
- High Threshold: The fill bleeds past edges and can cover the whole layer if your boundaries are soft or broken.
Fix edge fringing by nudging the Threshold up a few points rather than switching tools. If you see white specks or halos near textured brush lines, the strokes probably aren't fully opaque, so raising the Threshold slightly usually closes them. For production-clean flats, many illustrators draw linework with a solid, hard-edged brush so fills behave predictably.
Other ways to fill color in Procreate
ColorDrop isn't the only method, and some jobs suit alternatives better.
Recolor
Recolor is an older fill tool that Procreate brought back. It's accessed through QuickMenu, which is off by default.
- Go to Actions → Prefs → Gesture Controls → QuickMenu and enable it.
- Assign Recolor to one of the radial options.
- Open QuickMenu and tap Recolor, select your color, and tap areas to fill.
- Use the Flood slider to set how aggressively it fills.
Recolor is useful when you prefer tap-to-fill with a persistent mode over a drag gesture.
Selections with Color Fill
For geometric shapes or hand-drawn regions, use Selections → Color Fill.
- Tap Selections at the top.
- Choose a method: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it's highlighted blue.
- Pick your color, then make the selection. The area fills as soon as you complete it.
Procreate remembers the Color Fill setting between selection sessions, so turn it off when you're done or it will fill your next selection unexpectedly. Color Fill also works on a single layer only, not a layer group.
Fill Layer
To flood an entire layer with one color, choose your color, open the Layers panel, tap the layer twice to open Layer Options, and select Fill Layer. This is handy for solid backgrounds or for creating a flat color base you'll mask or alpha-lock later.
Troubleshooting: why ColorDrop fills the whole canvas
These are the most common causes when a fill floods everything or doesn't work.
- Threshold too high. The most frequent culprit. Drop the color, keep holding, and slide left to reduce the percentage.
- Open gaps in your linework. If the shape isn't closed, the fill escapes. Zoom in and patch small breaks with a hard brush on the line layer.
- You're filling an empty layer. ColorDrop reads the active layer's pixels. On a blank layer, there's no boundary, so the whole layer fills. Either draw on the same layer or set your linework layer as a Reference layer.
- A Reference layer is unexpectedly active. If a layer is marked Reference, fills on other layers follow that layer's contents instead of the one you're on. Open the Layers panel, tap the Reference layer, and toggle it off if you don't want that behavior.
- A paused or tapped drag. Pausing on the color dot before dragging can cancel the gesture. Use one continuous sweep.
- Semi-transparent or textured lines. Soft brushes leave partial-opacity pixels that the fill treats as gaps. Redraw boundaries with a solid brush or increase the Threshold.
A sensible setup for flat-color work: linework on one layer set as Reference, a separate color layer beneath it, and ColorDrop used on the color layer. You get clean fills that follow the lines without altering them.
A clean fill workflow for animation-bound art
If your Procreate art is headed into motion, a few habits save time downstream.
- Separate by element. Put each character part, prop, or background piece on its own layer so it can be moved independently in After Effects or Blender.
- Fill on dedicated color layers. Keeping flats apart from linework lets you restyle or re-color without redrawing.
- Check edge quality at 100% zoom. Fringing from a low Threshold shows up as thin halos once you composite over a different background.
- Export deliberately. Choose an export format that suits the compositing software you'll use next.
Taking filled Procreate art into motion
Procreate is a strong place to build key art, style frames, and character designs. Turning that into moving footage is a separate problem, and one where artists often want to keep their own drawing intact rather than hand it to a one-click generator.
This is where Styleframe fits.
It doesn't replace the drawing work you did in Procreate. Think of it as a way to extend a set of carefully filled frames into motion while retaining control over what the frames look like.
Quick reference
Final tips
Practice the drag gesture until it's one smooth sweep, because hesitation at the start can stop a fill from registering. Use the Threshold slider as your main control instead of redrawing lines. Keep linework and color on separate layers, and set linework as the Reference when fills need to follow it across layers. Once your flats are clean, you'll have layered, production-friendly art ready for whichever pipeline comes next, whether that's a keyframed After Effects comp, a Blender scene, or a generative pass in Styleframe.