How to Do Symmetry on Procreate
StyleFrame Team7 min read
To use symmetry in Procreate, tap the Actions (wrench) icon, open Canvas, switch on Drawing Guide, tap Edit Drawing Guide, and choose Symmetry. Pick Vertical, Horizontal, Quadrant, or Radial under Options, make sure Assisted Drawing is on, and tap Done. Then enable Drawing Assist on the layer you want to draw on, and every stroke will mirror across the guide in real time.
The rest of this guide covers each step in detail, what the four modes do, how to move and rotate the guide, and how to bring symmetrical artwork into a motion pipeline.
Step-by-step: turning on symmetry in Procreate
Symmetry lives inside Procreate's Drawing Guide system, so you have to enable the guide before you can configure it.
- Tap the Actions icon (the wrench) in the top left.
- Open the Canvas tab and toggle Drawing Guide on.
- Tap Edit Drawing Guide to open the Drawing Guides screen.
- Tap Symmetry at the bottom of the screen. Vertical symmetry is the default.
- Tap Options and choose a mode: Vertical, Horizontal, Quadrant, or Radial.
- Confirm Assisted Drawing is toggled on, then tap Done.
On Procreate Pocket the path is slightly different. Go to Modify > Actions > Guides, tap Symmetry, then tap Guide Settings to reach the same Drawing Guides screen.
Enable Drawing Assist on your layer
This is where most people get stuck. Symmetry only applies to layers that have Drawing Assist switched on. A layer with it enabled shows an "Assisted" label under its name. If you draw and nothing mirrors, tap the layer in the Layers panel and tap Drawing Assist.
Each new layer you create needs this toggled separately, so if symmetry works on one layer and not the next, that's almost always the cause. It also means you can mix assisted and unassisted layers in one file, for example a symmetrical body on one layer and freehand asymmetrical details on another.
The four symmetry modes
Each mode changes how many copies of your stroke Procreate generates and where it puts them.
Vertical symmetry
A guideline runs down the center of the canvas. Whatever you draw on the left appears on the right and vice versa. This is the right choice for faces, bottles, vases, logos, character front views, and anything with a clear left/right mirror. Because you can rotate the guide, you can also create mirroring along an angle.
Horizontal symmetry
The guideline runs across the middle, and the top half mirrors to the bottom. It's useful for reflections in water, top/bottom-mirrored shapes, and landscapes with a mirrored horizon. Since you can rotate any guide, vertical and horizontal are really the same tool at different angles. Choosing one just saves you a rotation.
Quadrant symmetry
Both a horizontal and a vertical guideline divide the canvas into four quadrants. A stroke in one quadrant is reproduced in the other three. This is the fastest route to tile-like designs, kaleidoscopic motifs, and centered emblems.
Radial symmetry
Radial splits the canvas into eight segments using horizontal, vertical, and diagonal guidelines. A stroke in one segment repeats across the rest. It suits mandalas, snowflakes, rosettes, and radial UI or HUD elements.
One limitation to know about: Procreate gives you fixed configurations (effectively 2, 4, and 8 divisions), not a freely adjustable count. Users have asked for a slider to choose the number of grid lines, and some artists who need 3 or 5-fold symmetry use a dedicated symmetry app for the base and bring the result into Procreate. If you need an unusual segment count, plan for that.
Mirror vs. Rotational symmetry
New guides default to Mirror Symmetry, which reflects and flips your stroke across the guideline. This is what you want for faces and objects.
Switching on the Rotational Symmetry toggle changes the behavior. The copy is reflected and rotated, which means it is flipped horizontally and vertically at the same time. The result feels more like a pinwheel than a mirror. Try both on a simple curve to see the difference before you commit to a design. Rotational is often better for ornamental patterns and spinning motifs, while Mirror is better for anything representational.
Moving, rotating, and resetting the guide
On the Drawing Guides screen, two nodes control the grid:
- Blue node (positional): drags the whole grid across the canvas, so the mirror axis doesn't have to be at the center.
- Green node (rotational): rotates the guidelines to any angle.
To snap everything back to the default position, tap either node and tap Reset.
Off-center axes are underused. If you're drawing a three-quarter character view or an asymmetrical composition with a symmetrical element in it, move the axis to the element's center instead of redrawing on a separate canvas.
Customizing how the guide looks
Three sliders control the guide's visibility without affecting the artwork:
- Color: the hue bar at the top of the Drawing Guides screen. Pick a color that contrasts with your palette so the guide stays readable.
- Opacity: from invisible to fully opaque.
- Thickness: from invisible to noticeable.
Guides appear as thin lines that overlay your artwork.
Assisted Drawing also nudges your strokes to follow the guide direction. It's on by default in Symmetry mode. Tap Cancel to leave without changes or Done to commit them.
Troubleshooting common problems
Nothing mirrors. Check that Drawing Guide is toggled on under Canvas, and that Drawing Assist is enabled on the active layer.
It mirrors on the wrong axis. You're probably in Horizontal when you wanted Vertical, or the guide has been rotated. Open Edit Drawing Guide and tap Reset on a node.
The mirrored side looks flipped the wrong way. Toggle Rotational Symmetry on or off.
A new layer lost symmetry. Drawing Assist is per layer. Re-enable it.
Lines look uneven near the axis. Assisted Drawing may be pulling strokes toward guide directions. Turn it off if you want strictly free strokes, though mirroring will still follow the guide on assisted layers.
A practical workflow: building a seamless symmetrical motif
A reliable way to use symmetry for pattern or graphic work, such as a blender print or a repeating element:
- Start with a canvas at a high resolution. One surface-pattern workflow uses 12x12 inches at 300 dpi.
- Turn on Quadrant symmetry and draw a light construction shape, such as a diamond, on a template layer. You'll delete it later.
- Add a background fill layer underneath.
- Add a new layer above the template, enable Drawing Assist, switch to Radial symmetry, and draw your motif inside the construction shape.
- Duplicate the layer and position the copies at the corners with snapping and magnetics on, so the edges meet at the center. Remove any marker marks you used for alignment.
The same approach works for non-pattern work. Draw one half of a character, prop, or emblem and let the guide do the rest, then refine details on a separate unassisted layer so the asymmetry reads as intentional.
Getting symmetrical Procreate art into a motion pipeline
If you're a motion designer, animator, or compositor, Procreate is usually a source of design assets rather than the final stop. Some practical habits:
- Keep elements on separate layers. Symmetrical bodies, ornaments, and backgrounds should be separate so you can animate them independently in After Effects.
- Export at a size you can scale. Work large; you can't invent detail later without help.
- Use clean, simple shapes for symmetry. Mirrored artwork often becomes a reference for rigging, loops, or radial animation, where precise axes matter.
- Flatten decisions about the axis early. Once the guide is set and layers are drawn, moving the center means redrawing.
Quick reference
Symmetry in Procreate is quick to set up once you know the two gotchas: enabling the Drawing Guide, and enabling Drawing Assist on each layer. After that, the work is choosing the right mode, placing the axis deliberately, and keeping your layers organized so the artwork is ready for whatever animation or compositing comes next.