How to Do Proper Pen Smoothing on Procreate
StyleFrame Team7 min read
Proper pen smoothing in Procreate means combining three controls in Brush Studio's Stabilization tab: StreamLine to clean up wobble, Stabilization to average the stroke path, and Motion Filtering to smooth the line independent of drawing speed. Set them per brush, and use the global Pressure & Smoothing preference only when you need the same smoothing everywhere. Start with moderate values, test on the Drawing Pad inside Brush Studio, and lower them for any brush where lag or lost corners show up.
What "Smoothing" Actually Means in Procreate
Procreate builds each stroke from many sampled points along the path of your Apple Pencil or finger. Smoothing changes how those points are filtered before the brush stamps along them. Three separate systems do this, and they behave differently:
- StreamLine removes shake and small wobbles from the line. It has an Amount slider and a Pressure slider. Pressure controls how gradually pressure changes are applied along the stroke.
- Stabilization takes a moving average of the stroke. Higher values smooth wobbles more aggressively and tend to straighten the line. Its effect depends on how fast you draw, and faster strokes come out smoother.
- Motion Filtering smooths the line regardless of stroke speed. It also has an Expression control that reintroduces a little organic variation so the result doesn't look mechanical. Expression only has an effect when Motion Filtering has some amount applied.
Most "my smoothing feels wrong" problems come from stacking all three at high values, or from forgetting a global setting is active.
Step-by-Step: Set Up Smoothing on a Single Brush
Per-brush settings are the most controllable route, because you can tune each tool for its job: an inker, a sketching pencil, a flat-color fill brush.
- Duplicate the brush first. Swipe left on the brush in the Brush Library and tap Duplicate. Editing the original means losing your baseline.
- Open Brush Studio. Tap the brush once to select it, then tap it again to open its settings.
- Go to the Stabilization tab. You'll see StreamLine, Stabilization, and Motion Filtering sections.
- Zero everything out as a test. Draw a few curves and a long straight stroke on the Drawing Pad so you know the raw behavior of your hand and the brush.
- Raise StreamLine Amount first. This is the gentlest fix and usually solves most hand jitter.
- Add Stabilization if you need straighter lines. Add a small amount, then test both slow and fast strokes. Because it responds to speed, you'll feel it change as you vary your pace.
- Add Motion Filtering for consistency. If you want the same smoothing at any drawing speed, use this. Then add a bit of Expression to keep the line from looking over-processed.
- Tune StreamLine Pressure. Higher values give a longer, smoother ramp as pressure builds. Lower values make pressure respond sooner, which feels more immediate.
- Tap Done and test on the real canvas. The Drawing Pad is a good preview, but your actual artwork at your actual zoom level is the true test.
If you get lost, open the About this Brush tab and use Reset Brush to return to the original state.
Global Smoothing: When to Use It
Go to Actions > Prefs > Pressure & Smoothing to apply stabilization to every brush at once. This is useful if you have a tremor, are working on a small screen, or are tracing across many tools and want uniform behavior.
The risk is that it overrides brush design. If your Apple Pencil suddenly feels laggy or unresponsive, check this setting before you blame the brush or the hardware. A sensible approach is to start with a small value (around 10–15%), and to turn it back down when you switch from inking to sketching.
In the same menu you can tune the pressure curve, which affects how hard you need to press to get thicker, darker marks. It's closely related to smoothing, since a poorly matched curve can make a line look uneven even when the path itself is smooth.
Starting Values by Task
These are starting points based on common practice, not rules. Your hand speed, canvas size, and zoom level all change what feels right.
For coloring, heavy smoothing causes strokes to feel short and sluggish, so dial StreamLine down on those brushes. For gestural sketching, too much smoothing kills energy, so turn it off.
Pair Smoothing with Taper and Pressure
Smoothing handles the path. Line quality also depends on how width and opacity behave along that path. The Taper tab in Brush Studio lets you shape how a stroke begins and ends using the Pressure Taper control. A smoothed line with a clean taper reads as deliberate, whereas a smoothed line with blunt ends can look vector-like and stiff. If you want a hand-inked look, combine high StreamLine with a modest taper and a pressure curve that suits how hard you press.
Troubleshooting Common Problems
The pen feels delayed. Lower Stabilization and Motion Filtering first, then check global settings. Any averaging introduces some lag, which is the trade-off for smoother lines.
Corners are rounded off. High smoothing cuts corners. Use lower values on brushes meant for hard-edged shapes, or draw corners as separate strokes.
Lines look too perfect. Reduce Stabilization, then add Motion Filtering Expression back in. Smoothing works best when the line still feels like it came from a hand.
Lines are inconsistent between sessions. You probably have a global setting on, or you edited a brush you didn't duplicate. Reset the brush and re-check Prefs.
Strokes feel different at different zoom levels. Check the Brush scaling preference. Setting it relative to canvas keeps brush behavior consistent for brushes designed that way, which helps when you're switching between detail work and wide views.
Why This Matters for Animation and Motion Work
If you're a motion designer, animator, or VFX artist, Procreate is often where hand-drawn elements originate: character poses, logo sketches, hand-lettered type, matte paintings, and style frames. Smoothing decisions then become pipeline decisions.
- Consistency across frames. If you're drawing multiple key poses or frame-by-frame elements, lock your brush and smoothing settings before you start. Changing StreamLine halfway through a sequence produces visible shifts in line character that are hard to fix later.
- Line quality survives scaling. A wobble that looks minor at iPad zoom becomes obvious when the artwork is scaled up in After Effects or composited in Nuke. Working at a high canvas resolution gives you more room, but clean strokes at capture are still cheaper than cleanup later.
- Intentional imperfection. Some projects want boiling, wobbly lines. Others want precise, graphic strokes. Decide which before drawing, then set smoothing accordingly rather than trying to correct it afterward.
- Separate brushes for separate jobs. Keep a smoothed inker, an unsmoothed sketcher, and a light-touch fill brush in one custom set so you aren't adjusting sliders mid-session.
Where Styleframe Fits After the Drawing Is Done
Once your frames are drawn, the next question is often how to carry that look into motion.
The practical connection to smoothing is simple: reference-driven tools reflect the quality of your reference. Clean, deliberate linework from well-tuned brushes gives a style transfer a stronger, more consistent source to follow.
Quick Checklist
- Duplicate a brush before changing it.
- Test with the Drawing Pad using curves, straight lines, and quick flicks.
- Raise StreamLine first, then add Stabilization or Motion Filtering only if needed.
- Use Expression to keep lines from feeling mechanical.
- Keep global stabilization low or off unless you actually need it.
- Match smoothing to the task: high for ink, low for color, off for gesture.
- Lock your settings before drawing a sequence of related frames.
- Reset the brush from About this Brush if behavior drifts.
Good smoothing is subtle. The goal is a line that looks confident and intentional while still feeling like it was drawn by a person, and the way to get there is to treat each brush as its own tool and tune it for the job it does.