How to Do Colored Lineart Procreate
StyleFrame Team7 min read
In Procreate, the fastest way to color lineart is to keep the lines on their own layer, turn on Alpha Lock, pick a color, and tap the layer thumbnail and choose Fill Layer. Every line pixel recolors with no black fringe left behind. For several colors in one set of lines, paint on the Alpha Locked layer, or put a clipping mask above the lineart so the original stays intact. For colored areas between the lines, use Color Drop on a separate layer below the lineart.
What "colored lineart" means in Procreate
The phrase covers two different jobs, and the right method depends on which one you need:
- Recoloring the lines themselves. Black ink becomes red, blue, or a gradient. This is common for stylized illustration, character designs, and animation frames where outlines shift hue to match the lighting.
- Coloring the shapes the lines enclose. This is flat color or paint under or around the linework, the classic "fill" workflow.
Both start with the same rule: lineart lives on its own layer. If sketch, lines, and color are on one layer, every later change is destructive. That matters even more if the art will be animated, composited, or restyled downstream.
Method 1: Alpha Lock and Fill Layer
This is the simplest way to turn black lines into one flat color.
- Open the Layers panel and select the layer that holds your lines.
- Tap the layer thumbnail and choose Alpha Lock. The layer shows that it is active.
- Open the Color panel and choose the new line color.
- Tap the layer thumbnail again and choose Fill Layer.
Alpha Lock restricts any change to pixels that already exist on the layer, so the fill only affects your lines. Transparent areas stay transparent. You can also drag the color swatch from the top-right corner straight onto the canvas to fill the locked layer. If it fills the wrong area, undo and check that the right layer is selected and Alpha Lock is on.
To go back to black, set your color to black and run Fill Layer again. Turn Alpha Lock off when you want to draw new strokes outside the existing lines.
Method 2: Multiple colors within the same lines
Flat single-color lines are often not what you want. Colored lineart usually varies, with warm outlines near a light source, cool outlines in shadow, or a different color per object.
With Alpha Lock still on:
- Paint directly. Choose any brush and paint over the lines. The strokes only land where lines exist, so you can't spill outside them. Use a soft airbrush for gradual transitions, or a hard brush for crisp color changes.
- Blend colors. Use a soft brush at low opacity to blend two colors across the same stroke.
This is how you get lines that read as part of the lighting rather than a black cage around the colors.
Method 3: Clipping mask for non-destructive color
Alpha Lock changes the pixels of your lineart layer. If you might want the original black lines back, or you plan to try several color schemes, use a clipping mask instead.
- Duplicate nothing. Leave your black lineart layer untouched.
- Add a new layer directly above it.
- Tap the new layer and choose Clipping Mask. It now only shows where the layer beneath has pixels.
- Fill or paint on the clipped layer with any color.
The black lines remain below, and the color sits on top. You can hide the clipped layer to return to black, add several clipped layers for different color treatments, or change a clipped layer's blend mode and opacity.
For revisions or client rounds, this is the safest approach. A change request becomes a layer toggle instead of a redraw.
Method 4: Coloring the shapes between the lines
If the goal is filled color areas, the structure flips: color goes below the lineart.
Color Drop with a Reference layer
- Make sure your lineart forms closed shapes. Gaps let color leak.
- Set the lineart layer as Reference (tap the layer, choose Reference).
- Create a new layer underneath the lineart for color.
- With the color layer active, drag a color from the top-right swatch into a shape. Hold the drop, then slide left or right to adjust Color Fill Threshold if the fill doesn't reach the edges.
Because Reference reads the lineart layer but the color lands on a different layer, your lines stay clean and the fill tucks under them. If you see a thin gap between color and line, raise the threshold, or paint a bit past the edge on the color layer and let the lineart cover it.
Multiply layer for painted color
For a more painterly look, add a layer above the lineart, set its blend mode to Multiply, and paint. Dark lines stay visible through the color, and you can lock the lineart layer to avoid accidents. This works well for loose, marker-style illustration but makes later colorway changes harder than flat fills on separate layers.
Fixing common problems
- Jagged or haloed edges. If a fill leaves a light or dark fringe, you probably filled on a layer without Alpha Lock, or Color Drop is working on a layer with soft edges. Use Alpha Lock for recolors, and increase the fill threshold for shape fills.
- Color won't stay inside the lines. Check that Alpha Lock is on, not just that the layer is selected.
- Lines look flat after recoloring. Use Method 2 to add variation. Uniform color often reads as less polished than subtle hue shifts.
- Fill covers the whole canvas. You ran Fill Layer without Alpha Lock. Undo and lock first.
- Lineart looks different against dark backgrounds. Preview over your actual background early. Light or saturated lines that look fine on white can disappear on a dark comp.
Preparing colored lineart for animation and compositing
If you work in After Effects, Premiere Pro, Blender, or Nuke, treat Procreate as an asset-building stage and plan the handoff.
- Keep layers separate. Lineart, flat color, shadows, and highlights on different layers give you control later.
- Use a transparent background. Hide the background layer before exporting a PNG so alpha comes through. Check your interpretation settings in your compositing software if edges look fringed.
- Name and order layers consistently. This saves time when you rebuild the stack in After Effects or Photoshop.
- Work at the final resolution. Upscaling hand-drawn lines later softens them. Set a canvas size that matches your delivery frame, or larger.
- Frame-by-frame work. The same Alpha Lock and clipping mask techniques work per frame. Export your frames as images for editing elsewhere.
Where Styleframe fits after the lineart is done
Once you have clean colored lineart, a common next question is how to carry that look into motion without redrawing every frame. Styleframe is an AI video and motion tool that works from your references rather than from a text prompt alone, so your Procreate artwork can serve as a reference. Your compositing workflow stays where it is, and Styleframe adds a controlled generation step to it.
AI output still needs review. Check line weight consistency, color accuracy against your palette, and frame-to-frame stability before approving a sequence. Those checks belong in your comp, with the tools you already use.
Quick reference
FAQ
How do I change line color in Procreate without affecting the rest of the layer? Turn on Alpha Lock for the lineart layer, choose a color, and use Fill Layer. Only existing line pixels change.
Can I recolor lines non-destructively? Yes. Add a layer above the lineart, set it as a Clipping Mask, and paint or fill on it. Hide it to see the original lines.
Why does my color fill leave gaps next to the lines? Color Drop's threshold is probably too low, or the lineart edges are soft. Raise the threshold or put the color layer beneath the lines and extend it slightly under them.
What should I export for After Effects? Keep your layers separate. A PNG with a transparent background works for single flattened elements. For animation, export frames as images and import them as a sequence.