How to Dim a Layer in Procreate
StyleFrame Team8 min read
To dim a layer in Procreate, open the Layers panel, tap the "N" next to the layer, and drag the Opacity slider left. A faster shortcut is to tap the layer with two fingers and slide left on the canvas. If you want the layer darker instead of more transparent, switch its blend mode to Multiply, or use Adjustments > Hue, Saturation, Brightness to lower its brightness.
"Dim" can mean two different things, so the right method depends on whether you want a layer to recede or to get darker. The sections below cover both, plus the non-destructive habits that keep a layered file safe to hand off to After Effects, Photoshop, or a 3D package.
Dimming vs. darkening: pick the right goal
Procreate has no single "dim" control. Artists use the word for several different outcomes:
- Making a layer less visible so what's beneath it shows through. This is opacity.
- Making a layer's colors darker while it stays fully opaque. This is brightness, curves, or a blend mode.
- Pushing a layer back in a composition, such as a background plate or a sketch you're tracing over. This is usually opacity, sometimes combined with a desaturation.
If you work in After Effects, the mapping is familiar. Layer opacity in Procreate behaves like the Opacity property. Brightness adjustments behave like Exposure, Levels, or Curves on an adjustment layer. Blend modes carry over almost directly, though not every mode renders identically across apps.
Method 1: Lower layer opacity from the Layers panel
This is the standard, non-destructive approach and the one to use by default.
- Tap the Layers icon (two overlapping squares) in the top right.
- Find the layer you want to dim.
- Tap the letter to the right of the layer name. It reads "N" when the blend mode is Normal.
- Drag the Opacity slider to the left. The percentage is displayed as you move.
At 100% the layer is fully visible. At 50% it is half see-through. Because the slider adjusts a layer property rather than changing pixels, you can return and change the value as often as you like without losing any painted data.
This is the method to use for reference layers, underpaintings, line art you want to soften, and any element that may need to be rebalanced later.
Method 2: The two-finger tap gesture
When you're mid-painting, opening menus slows you down. The gesture does the same job:
- Open the Layers panel.
- Tap the target layer with two fingers at the same time.
- A slider bar appears at the top of the canvas.
- Slide a finger left on the canvas to reduce opacity, or right to increase it.
You can see the percentage as you drag, which makes it easy to land on a precise value. This edits the same layer opacity property as Method 1, so it is equally non-destructive. Only one layer can be adjusted at a time, so if you need to dim several, group them first and adjust the group (see below).
Method 3: Darken with Multiply or another blend mode
If the goal is to darken rather than fade, opacity alone can look washed out. Lowering the opacity of a colorful layer just reveals whatever is underneath, which often reads as "faded" instead of "dimmed."
For a shadow-like dimming effect:
- Create a new layer above the content you want to darken.
- Fill it with a dark color, such as a desaturated blue or a warm dark brown. Pure black tends to look flat.
- Tap the "N" and change the blend mode to Multiply.
- Adjust the Opacity slider in the same menu to control the strength.
- Optionally, clip it to the layer below (tap the layer, then choose Clipping Mask) so the darkening only affects that layer's painted area.
Multiply multiplies the base color by the blend color, so the result is darker and richer. Procreate's own documentation describes it as suited to darkening images and creating shadows. In blend modes other than Normal, opacity affects things like color intensity or darkness rather than just transparency, so it is worth testing the slider after changing modes.
Other modes such as Color Burn and Linear Burn also darken, but they increase contrast or change saturation in ways that are harder to control. Start with Multiply and move on only if you need a different look.
Method 4: Adjust brightness directly
When you want the layer's own pixels to be darker, use an adjustment:
- Select the layer.
- Tap the Adjustments icon (the magic wand) and choose Hue, Saturation, Brightness.
- Choose Layer as the target rather than Pencil.
- Slide to lower Brightness. Lower Saturation too if you want a more muted result.
Curves gives finer control if you want to dim only the highlights or lift the blacks. These adjustments are applied to the layer's pixels when you commit them, so they are destructive. Duplicate the layer first if you might want to go back. A duplicate takes seconds and saves a lot of rework.
A note on Adjustments > Opacity and selection opacity
Procreate also has an Opacity option in the Adjustments menu, and a way to change opacity on just a selection. These behave differently from the layer property:
- Adjustments > Opacity works on the active layer's contents and is committed when you tap another tool or the Adjustments icon. You can cancel before committing.
- Selection opacity (select an area, then two-finger tap the layer and slide) changes only the selected pixels, and the change is applied when you exit that mode. Procreate's help documentation notes that this is a destructive action: you can undo it immediately, but you can't revisit the value later.
If you need to dim just part of a layer, a safer route is to put that part on its own layer or use a mask-like approach with a clipped layer, then use standard layer opacity.
Dim multiple layers at once with groups
Opacity is a one-layer-at-a-time control. To dim several layers together:
- In the Layers panel, swipe right on layers to select multiple.
- Tap Group.
- Open the group's "N" menu and lower the group's opacity.
The group opacity applies to the composite of its contents rather than to each layer separately, which avoids the stacking problem where overlapping semi-transparent layers show through each other. That is also a good way to keep a file organized for handoff.
Common problems and fixes
The slider doesn't seem to do anything. Check that you've selected the right layer and that it has content. A blank layer will appear unchanged.
The layer looks washed out, not dim. Use Multiply with a dark color instead of lowering opacity, or combine a small opacity reduction with a brightness adjustment.
Brush strokes are too faint, not the layer. That is brush opacity, controlled by the lower slider on the sidebar. Many brushes are also affected by Apple Pencil pressure, so a faint stroke at full brush opacity may be a pressure setting.
Edits can't be changed later. You probably used an Adjustments option or selection opacity. Layer opacity and blend mode changes stay editable; adjustments commit to pixels.
Taking dimmed Procreate layers into a motion pipeline
Many motion designers and VFX artists use Procreate for concept frames, boards, matte paintings, and hand-painted texture elements. A few habits make those files easier to use downstream:
- Keep dimming non-destructive. Layer opacity and blend modes stay editable in Procreate, so you can adjust them before export. Adjustments baked into pixels don't give you anything to tweak in After Effects or Photoshop.
- Name your layers and groups. Labels like "BG_dim" and "shadow_multiply" save time when you're rebuilding the stack in a compositor.
- Check blend modes after import. Common modes like Multiply may carry over, but verify against your reference export, since rendering can differ slightly between apps.
- Export a flattened reference too. It gives you a ground truth to compare against after you bring layers into your comp.
Procreate also isn't built for animating opacity over time in the way a compositor is. If you need a layer to dim across a shot, export the layer and keyframe its Opacity in After Effects or Premiere Pro rather than trying to fake it frame by frame.
Quick reference
For most cases, start with the opacity slider. If the result looks faded, move to a Multiply layer. Reserve direct adjustments for cases where you've duplicated the layer and want the pixels themselves changed.