How to Decrease Opacity of Layer in Procreate
StyleFrame Team7 min read
To decrease the opacity of a layer in Procreate, open the Layers panel, tap the small "N" to the right of the layer name, and drag the Opacity slider to the left. A faster route is to tap the layer with two fingers at the same time and slide left on the canvas. The slider method is non-destructive, so you can change the value again at any point.
Quick steps: lower layer opacity in Procreate
- Tap the Layers icon (the two overlapping squares) at the top right.
- Pick the layer you want to fade.
- Tap the "N" (or whichever blend mode letters appear) beside the layer name.
- Drag the slider under the blend mode label to the left. The percentage drops as the layer becomes more see-through.
Opacity in Procreate describes how visible a pixel is. At 100% a layer is fully visible, and at 50% it is half see-through. It can be controlled in three places: the brush, the whole layer, and a selection. These behave differently, and mixing them up causes most of the confusion people run into.
Method 1: the layer opacity slider
The "N" is the blend mode indicator. "N" stands for Normal, and tapping it opens the blend mode list along with the Opacity slider.
This is the most reliable method because:
- It applies to the entire layer, regardless of any active selection.
- The value stays editable. You can return and change it as often as you like.
- It leaves the underlying pixels unchanged.
If you have a selection active and use this slider, the whole layer still changes, not just the selected area. That surprises people who expect it to affect only the selection. If you want to fade only part of a layer, use the selection method below.
Method 2: the two-finger gesture
For quick adjustments, tap a layer in the Layers panel with two fingers at once. A control appears at the top of the screen, and sliding a finger left on the canvas lowers opacity while sliding right raises it.
This is useful when you want to judge the fade against the artwork rather than a number. You can watch how the layer sits against the layers below while you drag.
A few practical notes:
- The two-finger tap must land on the layer in the panel, not on the canvas. A two-finger tap on the canvas triggers undo if you have that gesture enabled.
- With a selection active, the gesture affects the selected area on that layer (see the next section).
Method 3: opacity on a selection only
If you only want part of a layer to become more transparent, make a selection first.
- Open the Selection tool and choose your preferred method.
- Make the selection.
- Open Layers and tap the target layer with two fingers at the same time.
- Slide left on the canvas to reduce opacity, or right to increase it.
Be careful here: this is destructive. Once you leave the adjustment mode, the change is applied to the pixels. You can undo immediately, but you can't come back later and tweak the percentage the way you can with the layer slider. Each use is a committed edit.
If you may want to revise the fade later, a safer approach is to copy the selected area to its own layer (for example with a copy-and-paste or a cut-to-new-layer action), then lower that layer's opacity with the standard slider. You end up with one extra layer, but the fade stays adjustable.
Method 4: brush opacity
Layer opacity and brush opacity are separate. Brush opacity controls how strong each stroke is as you paint. To change it:
- Select a brush.
- Use the lower slider in the sidebar.
- Drag down to decrease opacity, up to increase it.
If strokes look too faint even though the slider is maxed out, check Apple Pencil pressure settings. Many brushes respond to pressure, so a light touch can produce transparent marks regardless of the slider value.
Brush opacity only affects new strokes. It will not fade anything you've already painted. For that, you need one of the layer or selection methods above.
Troubleshooting common opacity problems
The slider changes the whole layer, not my selection. That's expected. The slider is layer-wide. Use the two-finger layer tap for selection-only changes.
Two-finger tap on the layer undoes my stroke. You're tapping the canvas instead of the layer row. Tap the layer name in the Layers panel.
My brush is too faint at 100%. Check pressure sensitivity and the brush's own settings.
A clipped layer won't color the layer below. Clipping masks restrict painting to the pixels of the layer beneath. If strokes seem to disappear, check whether the layer is clipped. This is intentional behavior and helpful for shading, but it can look like an opacity problem.
The layer looks faded but the slider says 100%. Check the blend mode and whether a lower-opacity layer sits above it.
Practical tips for motion and VFX artists
If you're using Procreate for textures, matte paintings, storyboards, or style frames that end up in After Effects, a few habits save time later.
Keep opacity as a layer property, not baked pixels. Use the layer slider where possible, so the fade stays editable. Check how your own export behaves in After Effects, as results can vary with blend modes and grouping.
Avoid destructive selection fades on assets you'll animate. If a piece of artwork may later fade in or out, keep it on a separate layer. In After Effects you'll animate opacity with keyframes, and clean layer separation makes that simple.
Name layers before export. Lower-opacity glow, haze, and shadow passes are easy to lose track of. Clear names make the handoff to a comp much smoother.
Test blend modes in the destination app. A layer that looks right at 60% in Procreate may behave differently in a comp, depending on color management and blend mode handling. Treat Procreate's preview as a guide, not a guarantee.
Export a flattened reference. Keeping a flat PNG next to the layered file gives you a visual target to match when you rebuild the look in After Effects.
Where Styleframe fits after Procreate
Procreate is strong for drawing and painting stills. Many artists carry Procreate frames into After Effects and animate opacity, position, and masks by hand. That works well for simple moves. For more complex motion, such as a character turning or an illustrated scene changing style, it takes a lot of manual work.
Styleframe is an AI video and motion tool built for artists who want direct control over the result. You can use your Procreate artwork as a starting reference, so the result comes from your artwork rather than a text prompt alone.
Styleframe is designed to fit into an existing pipeline rather than replace it, so you can bring the results into After Effects or Nuke for the finishing work you already do: opacity keyframes, color, grain, and final comp.
A practical workflow looks like this:
- Paint or refine your frames in Procreate, with fades set using layer opacity.
- Export the artwork, either flattened or as a layered file depending on the need.
- Use the frames as references in Styleframe to generate motion or a restyled version.
- Bring the result into After Effects or Nuke.
- Finish with opacity animation, blending, and color in the comp.
Summary
- Use the layer opacity slider (tap "N") for editable, whole-layer fades.
- Use the two-finger layer tap for fast, visual adjustments, or for selection-only changes.
- Remember that selection opacity is destructive, so move the selection to its own layer if you may need to revise it.
- Use the brush opacity slider only for future strokes, and check Apple Pencil pressure if marks look too faint.
- When the artwork is headed to a motion pipeline, keep opacity as a layer property and name your layers, so the handoff to After Effects or Nuke stays clean.