How to Decrease Opacity in Procreate
StyleFrame Team6 min read
To decrease opacity in Procreate, open the Layers panel, tap the "N" beside the layer, and drag the Opacity slider left. A faster route is to tap the layer with two fingers and slide left on the canvas, which shows an opacity percentage at the top of the screen. For brush strokes, drag the lower slider in the sidebar downward before you paint.
Procreate has three places to lower opacity: the brush, a whole layer, and a selection. Each behaves differently, and only one of them is destructive.
What Opacity Means in Procreate
Opacity is how visible a pixel is. At 100% it is fully visible, and at 50% it is half see-through. If you come from After Effects, this is the same idea as a layer's Opacity property. The difference is that Procreate applies it at three levels, and the controls are tucked into gestures and small UI labels that are easy to miss.
Choose the method by what you want to change:
- Brush opacity changes how strong future strokes are.
- Layer opacity changes how visible everything on one layer is, and you can revise it at any time.
- Selection opacity changes only the selected pixels on a layer, and the change is permanent once applied.
Method 1: Decrease Brush Opacity
Use this when you want strokes to build up gradually, such as soft shading or glazing, rather than going down at full strength.
- Select a brush.
- Find the sliders in the sidebar. The lower slider controls opacity.
- Drag it downward to decrease brush opacity.
This only affects strokes you make afterward. Existing paint stays as it is.
If your brush is still too faint
The reverse problem is common: the slider is at maximum but the stroke looks transparent. Many brushes also respond to Apple Pencil pressure, so a light touch can produce a weaker mark even with opacity maxed out. Before assuming something is broken, press harder, then check your pressure curve and the brush's pressure settings.
Method 2: Decrease Layer Opacity
This is the method you'll use most, and the one worth building habits around because it's non-destructive. You can change the value as often as you like without losing the original pixels.
Option A: The "N" menu
- Open Layers in the top right.
- Tap the letter beside the layer name. It reads N (Normal blend mode) by default.
- Drag the Opacity slider at the top of the menu to the left.
The same panel lists blend modes, so it's a good place to lower opacity and test a blend mode together.
Option B: The two-finger gesture
- Open Layers.
- Tap the layer with two fingers at the same time. The index and middle fingers of one hand work well.
- Slide left on the canvas to decrease opacity, or right to increase it.
An opacity bar and percentage appear at the top of the screen as you drag. You can use a finger or Apple Pencil. This is the faster option once it becomes muscle memory, and it lets you judge the result against your artwork rather than against a slider.
Two cautions:
- You can only adjust one layer at a time this way.
- If you have two-finger tap set to undo in your gesture settings, tapping on the canvas can undo a stroke. Tap the layer in the Layers panel, not the canvas.
Method 3: Decrease Opacity on a Selection
Sometimes you only need part of a layer to be more transparent, such as one shape or a patch of shading.
- Open Selections and choose a method (Automatic, Freehand, and so on).
- Make your selection.
- Open Layers.
- Tap the layer containing the paint with two fingers.
- Slide left on the canvas to reduce the opacity of the selected area, or right to increase it.
This is where people most often get stuck. The layer's opacity slider (from the "N" menu) still changes the whole layer, even when a selection is active. To affect only the selection, you must use the two-finger tap on the layer.
This one is destructive
When you leave this mode, the change is applied to the pixels. You can undo it right away, but you can't go back later and fine-tune it the way you can with layer opacity. Each application is final. If you may want to revise the result, a safer workflow is:
- Copy the selected area to its own layer.
- Lower that layer's opacity with the "N" menu or the two-finger gesture.
That keeps the adjustment editable.
Older Versions: The Adjustments Opacity Tool
In older versions of Procreate, you could go to Adjustments > Opacity, then slide left or right to change how transparent the active layer's contents were. A bar at the top showed the current value, starting at 100%. The buttons at the bottom let you cancel, undo, redo, or reset your changes, and you committed by tapping the Adjustments icon again or choosing another tool.
If you're following an older tutorial and can't find that tool, or you're confused about why the layers-tab opacity changes the whole layer, the two-finger gesture on the layer is the current equivalent for selections.
Troubleshooting Common Opacity Problems
The slider changes the whole layer, not my selection. Use the two-finger tap on the layer in the Layers panel instead of the "N" menu slider.
Two-finger tap undoes my stroke. You're likely tapping the canvas. Tap the layer in the Layers panel.
Brush opacity is at 100% but strokes look faint. Check pressure sensitivity and the brush's pressure settings.
I can't recover the original after changing a selection. Selection opacity is destructive once committed. Undo right away if you can, or use the duplicate-to-layer workflow next time.
A clipping mask doesn't paint outside the base layer. This is by design. A clipped layer only shows over the pixels of the layer beneath it, so strokes that seem to vanish may simply be outside that area. It also makes clipped layers handy for tinting or shading without touching the original paint.
Why Opacity Habits Matter for Motion Work
If you use Procreate for storyboards, style frames, texture passes, or hand-drawn elements that end up in After Effects, how you handle opacity affects what you hand off.
- Keep fades editable. Lowering opacity on a layer rather than on pixels means you can change your mind later or rebuild the same fade in After Effects.
- Separate elements that will animate. If a shape will fade in your composition, keep it on its own layer rather than merging it into a flattened painting.
- Check opacity after export. If you export layered files, verify how your values and blend modes arrive in After Effects, Photoshop, or Nuke before you rely on them.
Quick Reference
Start with layer opacity whenever you can. It's the one method you can revisit at any point, which makes it the safest choice when your Procreate work is headed for a longer pipeline.