How to Cut and Move in Procreate
StyleFrame Team7 min read
To cut and move something in Procreate, select it with the Selection tool (the S-shaped icon), tap Copy & Paste, and choose Cut & Paste. This puts the selection on its own layer, ready to move. Then use the Transform tool (the arrow icon) and drag from anywhere on the canvas to reposition it. Cutting to a new layer leaves the original layer untouched apart from the removed area, so you can adjust the moved piece without damaging anything underneath.
The Short Version
- Select the layer that contains the artwork.
- Tap the Selection tool and choose a mode such as Freehand.
- Select the area you want to cut.
- Tap Copy & Paste and choose Cut & Paste.
- Tap the Transform (arrow) tool and drag the new layer into position.
- Release your finger or stylus to confirm the move.
The rest of this guide covers what each step does, why "cut" and "move" behave differently in Procreate than in desktop apps, and how to avoid the problems that usually come up.
Step 1: Make a Clean Selection
Everything depends on the selection. Procreate only acts on the active layer, so check which layer is highlighted in the Layers panel before you select anything. If the wrong layer is active, you'll cut empty pixels or the wrong content.
The Selection tool has several modes, including:
- Freehand: Draw around the object with your Pencil or finger. Close the loop at the starting point (the gray dot). This is the best choice for irregular shapes and photo cutouts.
Once you have a selection, the toolbar at the bottom includes Copy & Paste, which is what you use to put the selection on its own layer.
Step 2: Cut the Selection to Its Own Layer
You have two ways to cut:
Option A: Cut & Paste (best for moving). Tap the Copy & Paste button in the selection toolbar and choose Cut & Paste. The selected pixels are removed from the source layer and placed on a new layer above it. Transform is then ready to use.
Option B: Cut. This removes the pixels and puts them on the clipboard. You then need a separate paste to bring them back. Use it when you want to paste into a different canvas or a different place in the layer stack.
If you want a copy and not a removal, choose Copy & Paste or Duplicate. This is the safer choice when you're not sure about the edit.
If you skip the cut and just transform a selection, Procreate moves the pixels on the same layer. The area they came from becomes transparent, and the moved pixels can be merged with whatever sits at the destination. That is often fine for quick sketches but awkward for anything you might revise.
Step 3: Move With the Transform Tool
Tap the arrow icon in the top toolbar. A bounding box appears around the content of the layer or selection. In Uniform mode:
- Drag anywhere on the canvas, inside or outside the box, to move the content.
- Pinch inside the box to scale from the center.
- Drag a corner or side node to scale from the opposite node.
- Use the green rotation handle to rotate.
The other modes handle bigger changes:
- Distort changes the angle of the art, which is good for fitting a piece into a perspective.
- Warp lets you push certain parts together, which suits organic shapes and cloth.
When the piece is in place, release your finger or stylus to confirm the move.
Moving Without Resizing
A common complaint is that a selection distorts when you try to move it. This usually happens when you touch a node or handle by accident. Place your Pencil or finger in empty canvas space outside the bounding box and drag from there. Because the drag doesn't start on a node, it only translates the content.
Step 4: Position Precisely
Dragging is fast but imprecise. Procreate gives you a few ways to be exact.
Nudging. With the Transform tool active, tap on the canvas outside the bounding box in the direction you want to move. Each tap shifts the content by a small increment. Tap below the object to move it down, and so on. This works for fine adjustments after a rough drag.
Snapping. The Snapping button in the Transform toolbar toggles guides on and off. Blue guides snap to other layers, and yellow guides snap to the canvas center and quadrants. Snapping helps when aligning pieces. It gets in the way when you're hand-fitting two images together, and many artists turn it off for that work.
Magnetics. Inside the Snapping menu, Magnetics lets you align content along an axis you define, which helps with consistent spacing and angles.
Step 5: Choose the Right Interpolation
Every transform resamples pixels, and the interpolation setting controls how. It sits in the Transform toolbar:
- Bicubic: The best default when scaling or dragging images around, since it keeps them from looking distorted or warped.
- Bilinear and Nearest Neighbor: The other two options. For most work, community advice is to stick with Bicubic.
Resampling is destructive. If you scale a piece down, commit, and scale it back up, you won't get the detail back. Duplicate the layer before large transforms, and do each transform in as few steps as possible.
Cutting a Photo Into Pieces and Recombining It
A common request is cutting an image into sections, rotating them, and reassembling them. This workflow holds up well:
- Duplicate the source layer and hide the original.
- Use Freehand selection to isolate each section, then Cut & Paste to put each one on its own layer.
- Turn off Snapping, then move and rotate each piece with Transform.
- Use Distort or Warp to fit edges together. Liquify (under the magic wand icon) can push areas into alignment.
- Group the pieces, duplicate the group, and merge the duplicate if you want to blend edges with the Smudge tool at low strength.
- For a cutout with no background, hide the background layers and export as PNG to keep transparency.
To keep painting and blending contained within a shape, use an Alpha Lock on the base layer, or place layers above it and set them as Clipping Masks. This keeps paint inside the piece and reduces cleanup erasing.
Common Problems and Fixes
- Nothing happens when you cut: The active layer is probably empty in the selected area. Check the Layers panel.
- The selection jumps when you move it: You grabbed a node. Drag from outside the bounding box.
- Edges look jagged after moving: Check that interpolation is set to Bicubic.
- A hole is left behind: You moved a selection without cutting to a new layer. Undo, then use Cut & Paste, or fill the gap on the lower layer.
- Multiple objects need to move together: Select multiple layers by holding one and tapping the others, or group them. Transform then acts on all of them.
- Text won't behave like paint: Text layers move with Transform. Tap the text for further adjustments like font, color, and style.
Taking Cut Pieces Into a Motion Pipeline
For motion designers, cutting and moving in Procreate is often prep work. Separating a character or illustration into pieces on distinct layers is the first step in rigging it for animation. A workable approach:
- Keep every moving part on its own layer with a clear name: arm, forearm, hand, and so on.
- Paint a little past the visible edge where parts will overlap, so they don't show gaps when they rotate.
FAQ
Can I cut and move without creating a new layer? Yes. Select the area, tap Transform, and drag. The pixels move on the same layer and leave a transparent gap. A new layer is safer for anything you may want to change.
How do I move a whole layer? Select the layer, tap Transform, and drag. To reorder it in the stack, press and hold the layer in the Layers panel and drag it up or down.
Why does my artwork look soft after moving it? Each resample softens detail. Use Bicubic, limit the number of transforms, and avoid scaling up beyond the original size.
Cut to a new layer, transform once, keep a duplicate as a backup, and name your layers. Those habits make the work cleaner in Procreate and easier to carry into whatever tool comes next.