How to Cross Hatch Within a Drawing in Procreate
StyleFrame Team7 min read
To cross hatch within a drawing in Procreate, put your hatching on its own layer above the shape and clip it to that shape with a Clipping Mask (or Alpha Lock). Draw one set of parallel lines, then add a new layer, rotate the canvas, and cross the first set at a different angle. Add more passes only where you want darker values. Because the hatching is clipped, it can't spill past the outline, and you can erase, move, or warp each pass without damaging the line art.
How Cross-Hatching Works
Cross-hatching builds tone from intersecting sets of parallel lines. Sparse single-direction lines read as light shade. Adding a second set at an angle deepens the value, and a third or fourth pass pushes toward near-black. Density is the main dial, so the technique stays graphic and flat.
Before you draw any lines, decide three things:
- Form: what simple geometric shape sits under the object (sphere, cylinder, box).
- Shadow shapes: where the shadow falls and which planes turn away from the light.
- Light shapes: which areas stay nearly empty. You don't draw light, you leave it alone.
Taking a minute to note these makes the line work much more predictable.
Set Up Your Canvas, Brush, and Layers
A layered setup is what makes cross-hatching in Procreate manageable.
- Create the canvas at the size you'll need downstream. If the artwork will end up in a comp, work at the final resolution. Hatching that gets scaled up later will show soft, blurry line edges.
- Choose a brush with consistent line weight. A monoline or technical-style pen works for clean ink. For a scratchier look, try a dip-pen style brush with pressure response. Some third-party hatching sets include several line weights at fixed spacing, and some are designed so that rotating the canvas changes the stroke angle.
- Sketch on a separate layer. Block in the form in pencil at low opacity, then lower that layer further when you ink.
- Ink the outline on its own layer. Keep the contour separate from all hatching.
- Create one layer per hatching direction. Name them "hatch 1," "hatch 2," and so on. This is the single habit that saves the most time later.
Hatching Within a Shape, Step by Step
Step 1: Confine the Hatching to the Shape
You have two clean options for keeping lines inside an object.
Clipping Mask. Fill the shape on its own layer (a flat base color works). Add a new layer above it, tap the layer, and choose Clipping Mask. Anything you draw on that layer only appears where the base layer has pixels. This is the more flexible method because you can add as many clipped hatching layers as you want.
Alpha Lock. Select the layer and swipe two fingers to the right across it. Painting is now restricted to existing pixels on that layer. Use this when hatching directly on a filled shape layer. It's quick, but it's destructive, since the hatching and the fill share the layer.
If your shape isn't already on its own layer, tap the layer thumbnail and choose Select to generate a selection from the layer contents, or use the Selection tool in Automatic mode on a closed outline. Then add a layer and fill or hatch inside the selection.
Step 2: Draw the First Pass
On your first hatching layer, draw evenly spaced parallel lines across the darker areas of the form.
- Rotate the canvas with a two-finger twist so the strokes are comfortable for your hand. Quick, confident flicks look better than slow, careful lines.
- Keep spacing even. Your eye reads uneven spacing as accidental texture.
- Follow the surface. On a sphere or a cylinder, curve the lines around the form instead of drawing them dead straight. The curvature is what suggests volume.
- Use QuickLine for rigid shapes. Draw a line and hold at the end, and Procreate snaps it straight. This works well on architectural or mechanical subjects, but it can look stiff on organic forms.
Stay out of the highlight areas entirely. Start the lines in the shadow, and let them thin out as they approach the light.
Step 3: Add the Cross Pass
Create a new clipped layer above "hatch 1." Rotate the canvas, or tilt your strokes, so the new lines cross the first set at roughly 45 to 90 degrees. Draw them over the mid-shadow and shadow zones only, not the full area covered by the first pass.
Changing direction with each layer matters. Repeating the same direction just thickens the existing lines, which doesn't add tonal depth and looks dull. A crossing angle produces the woven texture that reads as shade.
Step 4: Build Values Gradually
Work from light to dark:
- Pass 1: sparse lines across the whole shadow side (light shade).
- Pass 2: crossed lines over mid-shadow (medium).
- Pass 3: a third angle, or tighter spacing, in the core shadow (dark).
- Pass 4: dense lines in the cast shadow or occlusion zones, where two surfaces meet (darkest).
Then step back, zoom out, and check the values. Squinting at the canvas helps. If an area feels too busy, erase selectively on that layer instead of redrawing it.
Step 5: Bend and Adjust the Hatching
Because each pass lives on its own layer, you can reshape it after the fact:
- Use Transform → Warp (or Liquify) on a single hatching layer to bend straight lines around a curved surface. Hatching rules don't need to stay perfectly parallel, and a slight warp often looks more hand-inked than a rigid grid.
- Nudge a layer with the Move tool if a pass is crowding the contour.
- Lower the opacity of a layer to soften an overworked area.
- Use the Eraser with the same brush to thin out lines near highlights.
Step 6: Clean Up and Finish
Hide your sketch layer, check the edges where hatching meets the outline, and tidy any gaps. If you want cross-hatching on top of color, set the hatching layers to Multiply so the lines darken the color beneath them. If you want pure black-and-white ink, keep the hatching layers on a transparent background so you can place them over any plate later.
Common Mistakes to Avoid
- Hatching everything at one angle. Without a crossing set, tone stays flat.
- Drawing lines straight across a rounded form. This makes volume read as a flat sticker.
- Making lines too short and fussy. Tight scribbles look nervous. Longer strokes with a steady rhythm look more controlled.
- Working on one layer. One merged layer means any mistake gets painful to fix.
- Hatching the highlights. Leave paper-white areas empty. Contrast depends on it.
- Working too small. A hatched drawing that looks fine on a tablet can turn muddy when scaled up in a comp.
Taking Hatched Artwork into a Motion Pipeline
Cross-hatching can suit motion work because it looks hand-made. Procreate's layer structure translates well to compositing.
Export for compositing. Export your layers in a format your compositing software can read, or hide the background and export a transparent image. Keeping each hatching pass as a separate layer lets you animate, offset, or time-shift it.
Create a boil. For the classic hand-drawn shimmer, draw two or three alternate versions of each hatching pass and cycle through them at a low frame rate. A truly redrawn boil has more natural variation than an effect applied to a single drawing.
Animate the passes. Because each direction is a separate layer, you can reveal hatching with a wipe or a mask animation, so the shading builds across the shot instead of appearing all at once.
Quick Reference
Final Thoughts
Cross-hatching within a drawing in Procreate comes down to disciplined layers: a base shape, a clip, and a separate layer for each hatching direction. Plan your light and shadow shapes first, build values gradually from sparse to dense, and keep every pass editable. That structure gives you clean artwork now and flexible, animatable assets when the drawing moves into After Effects, Nuke, or a style-transfer step later.