How to Copy Texture in Procreate
StyleFrame Team7 min read
To copy a texture in Procreate, open Adjustments → Clone, drag the disc over the texture you want, and paint it onto another part of the canvas with any brush. To move a texture patch as a whole, select it with the Selection tool, swipe down with three fingers to open Copy & Paste, then paste it where you need it. For reusable texture, import the texture as a grain source in Brush Studio so it becomes a brush you can paint with anywhere.
Each method suits a different job, so the sections below cover when to use which, plus how to carry the result into a motion pipeline.
Method 1: Copy Texture with the Clone Tool
Clone is the closest thing Procreate has to a stamp tool. It paints one part of your canvas onto another, using whichever brush you pick. That makes it the best choice for extending a texture, patching gaps, or hiding repeats.
Step by step
- Select the layer containing the texture you want to sample.
- Tap the Adjustments icon (the magic wand) and choose Clone at the bottom of the list.
- A disc appears in the middle of the screen. Drag it over the area you want to copy.
- Paint anywhere else with your finger or Apple Pencil. Whatever sits inside the disc is reproduced where you paint.
- Tap the Adjustments icon again to commit and leave the tool.
Controls worth knowing
- The disc follows your stroke. If you lift and paint again, the next stroke samples from the disc's new position.
- Lock the disc. Press and hold it until it pulses and a Clone lock notice appears. Every stroke then samples from the same spot. Press and hold again to unlock.
- Two sidebar sliders. The upper one controls brush size, and the lower one controls the strength of the cloning.
- Any brush works. Tap the brush icon while Clone is active to switch. A soft round brush gives smooth blends, while a grainy brush breaks up the edge of the copy.
- Limitation: Clone does not work while you are 3D painting.
Avoiding the obvious "copy-paste" look
Repeated patterns are the main giveaway of cloned texture. Three habits help:
- Vary pressure so each stroke has a different silhouette.
- Use a brush with grain so the edges don't read as a clean duplicate.
- Resample from a few different spots rather than locking the disc on one patch for the whole job.
Cleaning up a photographed texture
Clone is also handy before you copy a texture elsewhere. If you shot or downloaded a paper photo with a few dark flecks or fibers, sample a clean area and paint over the flaws. Once the surface is uniform, you can use the photo as an overlay or turn it into a brush without those flaws repeating across your artwork.
Method 2: Copy and Paste a Textured Area
When you want an exact copy of a region rather than a painted reproduction, use selection and the Copy & Paste menu.
- Open the Layers panel and select the layer holding the texture.
- Choose the Selection tool and set it to Freehand.
- Make sure Color Fill and the masking option are turned off, so you are selecting rather than filling or masking.
- Draw around the area you want.
- Swipe down with three fingers to open the Copy & Paste menu.
- Choose Copy (or Cut, or Duplicate), then paste and drag the patch into place.
Once pasted, use the Transform tool to scale, rotate, or flip the patch. Mirroring a pasted patch is a quick way to disguise that it was duplicated. For a textured background, paste several patches at different rotations, then erase or mask the seams on each layer.
Clone vs. copy and paste
Method 3: Turn a Texture into a Reusable Brush
If you keep copying the same texture, stop copying and build a brush from it. A brush lets you paint the texture with pressure sensitivity, at any scale, in any color.
- Create a canvas and place your texture on it, such as a photo of paper, concrete, canvas, or a scan of real media. Crop it square and adjust levels so the contrast reads clearly.
- Open the Brush Library and create a new brush (the plus icon).
- In Brush Studio, open the Grain settings and edit the grain source. Import or create your texture as the grain source.
- Adjust the grain settings so the brush behaves the way you want.
- Test the brush on a blank canvas, and tweak until the texture holds up at both small and large sizes.
If you want the texture to behave like a stamp, use it as the brush's shape source instead of the grain source. The same workflow of importing, adjusting, and testing applies.
Method 4: Layer a Texture Over Artwork with Blend Modes
Sometimes "copying" a texture really means applying a photographed texture across a whole illustration. This is non-destructive and the easiest to revise.
- Import the texture photo as its own layer above your artwork.
- Scale it to cover the canvas.
- Try blend modes such as Multiply or Color Burn. Some illustrators stack two texture layers with different blend modes for richer depth.
- Use Hue, Saturation, Brightness to desaturate the photo and adjust brightness, then fine-tune opacity.
- Use Clone on the texture layer itself to remove any distracting flecks.
Keeping the texture on separate layers means you can swap, hide, or rebalance it at any point before export.
Common Problems and Fixes
- Clone paints nothing. Check that you have the right layer selected and that the disc is sitting over content on that layer. Also confirm you aren't in 3D painting mode.
- The pattern looks tiled. Vary your brush, rotate pasted patches, and resample from several areas.
- The texture looks flat. Switch blend mode, lower opacity, or stack a second layer. A texture only becomes visible if it has contrast, so adjust levels on the source image first.
- The texture scales badly. Build the source at a higher resolution than your canvas needs. If you will later push the art into 4K video, start with a large canvas.
Taking Procreate Textures into a Motion Pipeline
For motion designers and compositors, Procreate is often where a texture or style frame is born, not where it ends up. A few practical handoffs:
- After Effects and Premiere Pro: Export a flattened PNG or a layered PSD from Procreate. Use PNG for clean overlays, and PSD when you want to keep layers and re-balance them in the comp. Place the texture above footage with Multiply, Overlay, or Soft Light, and animate its position or opacity for a boiling, hand-made feel.
- Cinema 4D and Blender: Use the exported image as a color, roughness, or bump input. Check that the texture tiles cleanly first, because seams that are invisible on a flat illustration show up quickly on 3D surfaces.
- Nuke: Bring the texture in as a Read node and use it for grain, dirt, or paper overlays in the comp.
Check your color profile and bit depth at export. A texture that looks right on the iPad display can shift when it lands in a different color-managed pipeline.
Where Styleframe fits
Procreate is excellent for authoring a texture or a single styled frame, but it doesn't animate that look. This is where can sit alongside it, letting you bring a textured Procreate frame in as a reference for video work.
The aim is not to replace your compositing workflow but to extend a hand-built Procreate texture into moving footage you can still finish yourself.
Quick Reference
- Clone: Adjustments → Clone → drag the disc → paint → tap Adjustments to commit.
- Lock the source: press and hold the disc.
- Copy & Paste: Selection (Freehand) → three-finger swipe down → Copy → Paste.
- Reusable texture: Brush Studio → Grain or Shape source → import → adjust.
- Full-canvas texture: import photo → blend mode → Hue/Saturation/Brightness → opacity.
Start with Clone for quick fixes and soft extensions, use Copy & Paste for exact patches, and build a brush once you notice yourself repeating the same texture. Each method keeps your artwork editable, which matters when that artwork moves on to a motion project.