How to Copy a Picture on Procreate
StyleFrame Team7 min read
To copy a picture in Procreate, swipe three fingers down the canvas to open the Copy & Paste menu and tap Copy. Swipe down again and tap Paste to place it on a new layer above your active layer. To copy a picture from outside Procreate, such as from a browser, long-press the image, tap Copy, then paste it into a canvas with the same gesture. To copy only part of your artwork, make a selection first. Copy All captures everything visible on the canvas.
The Fast Method: Three-Finger Swipe
The three-finger swipe is the default way to copy and paste in Procreate on iPad.
- Open the canvas and select the layer you want to copy from.
- Swipe three fingers down the canvas at the same time.
- Tap Copy (or Cut if you want to remove the original).
- Swipe down again and tap Paste.
Pasted content always lands on a new layer directly above the layer you had active. Select the layer you want your paste to sit above before you paste.
If the gesture does nothing, check Actions → Prefs → Gesture Controls → Copy & Paste, where you can enable it or change how it's triggered. Swipe with all three fingers touching the screen at the same moment. A staggered touch may keep the menu from appearing.
How to Copy a Picture From Outside Procreate
Most "copy a picture" searches mean bringing a reference or asset in from a browser or another app. The clipboard route works for these.
From a browser or another app
- Long-press the image until a menu appears.
- Tap Copy.
- Switch to Procreate and open a canvas.
- Swipe three fingers down and tap Paste.
The first time you paste from another app, iPadOS asks for permission. If you tapped the wrong option, go to Settings → Apps → Procreate and enable Paste from other apps. That setting only appears after you've attempted a paste at least once.
Saving images to your camera roll
One practical note: images saved from a browser to the camera roll can end up sorted by their original metadata date rather than the date you saved them, so they're hard to find. Copying straight from the browser avoids that. If you do save references, keep them in albums.
Starting a new canvas from the clipboard
You can also begin a canvas from what you copied. In the Gallery, tap the + button and use the Clipboard option in the canvas presets to start a new canvas from the copied image. Inside a canvas, Actions → Add → Paste does the same job as the gesture and is handy if gestures are disabled.
How to Copy a Picture Within Procreate
Which option you choose depends on whether you want a whole layer, a region, or everything visible.
Copy a whole layer
Tap the layer to open its Layer Options menu and choose Copy. This copies the entire layer's contents, or just the isolated area if you have an active selection. Then paste with the gesture or from the Actions menu.
Copy a selected region
- Tap the Selection tool and make your selection.
- Swipe three fingers down and tap Copy.
- Paste to create a new layer containing only that region.
Do not tap the Transform arrow before copying. In Transform mode, Copy can capture the whole layer rather than just your selection. Make the selection, copy, and only then start transforming the pasted result.
Copy everything you see
Copy All in the Copy & Paste menu captures everything currently visible on the canvas. It also works with an active selection, so you can grab a specific section of a composite. Actions → Add → Copy canvas does the same thing.
Duplicate and Cut & Paste
- Duplicate acts like a copy and paste in one tap, creating the copy immediately.
- Cut & Paste removes the layer contents or selected area and drops it back as a new layer, which is useful for separating elements that were painted on a single layer.
If you need a duplicate on a new layer so you can move it separately, copy and paste on the same layer. The paste lands above the original, and you can move it without touching what's underneath.
Copying a Picture Between Canvases
Procreate's copied content goes to the iPad's clipboard, so it persists when you leave a canvas.
- Copy the layer or selection in the first canvas.
- Return to the Gallery and open the second canvas.
- Swipe three fingers down and tap Paste.
To make a new document from the selection instead, use the Gallery's Clipboard preset described earlier. This helps when you need a cutout of an illustration as its own file.
Other Ways to Trigger Copy and Paste
- QuickMenu: Off by default. Enable it in Actions → Prefs → Gesture Controls → QuickMenu, then assign copy and paste actions to its radial slots. This is faster than the three-finger swipe if you use Apple Pencil and rarely lift your hand.
- Actions menu: The Add tab contains Copy, Copy canvas, and Paste options if you prefer menus over gestures.
- Layer Options menu: Best when you want the layer's contents, not a visible region.
Troubleshooting Common Problems
The menu doesn't appear. Confirm the gesture is enabled in Gesture Controls and that all three fingers land at once. Try QuickMenu or the Actions menu as an alternative.
Paste does nothing or the option is greyed out. The clipboard may not contain an image. Re-copy the picture and try again. If you copied from another app, check the paste permission setting.
It copied the entire layer, not my selection. Make sure the selection is active and you haven't entered Transform mode. If the selection mask was cleared, reselect.
The pasted picture is the wrong size. A pasted image may not match your canvas: a large image may spill beyond the canvas, and a small one may look tiny. Use Transform to fit it, and check the canvas resolution if quality matters.
I can't find the pasted picture. Look one layer above the layer that was active when you pasted. It's always placed there.
Taking Copied Pictures Into a Motion Pipeline
For motion designers, animators, and VFX artists, Procreate often serves as a sketchpad: a place to paint a keyframe, a texture, or a reference frame that then goes into a larger pipeline. Copy and paste is what gets assets in and out of that sketchpad cleanly.
A reliable pattern:
- Copy reference stills from a browser into a dedicated reference layer group.
- Paint or modify the key image on its own layers, using selections and Copy All to isolate pieces.
- Export your artwork in a format that suits the next tool, keeping layers or transparency if you need them.
- Bring the exported files into After Effects, Premiere Pro, Nuke, Blender, or Cinema 4D as footage, textures, or matte elements.
If the next step is generating motion from those still frames, is one place to look. You keep your compositing workflow, and Procreate remains the place where the key art is made.
Best Practices for Copying Pictures in Procreate
- Paste into a planned layer structure. Because paste lands above the active layer, select the right layer first and you won't have to reorder afterward.
- Use Copy All for flattened references. It captures what's visible on the canvas.
- Name and group layers early. Cleaning up a pile of copied layers is tedious.
- Mind your resolution. If pasted pictures will end up in a 4K comp, make sure the Procreate canvas is large enough, since scaling up a small paste softens it.
- Check usage rights on browser images. Use copied images as private reference unless you have permission to use them in finished work.
FAQ
Can I copy a picture in Procreate on iPhone? This guide covers Procreate for iPad. Steps in Procreate Pocket may differ, so check its Help Center.
Does copying a picture create a new layer? Pasting does. Copying itself only puts the content on the clipboard.
How do I copy just part of a picture? Use the Selection tool, make your selection, then copy and paste, avoiding Transform mode until after you've pasted.
How do I copy a picture to another app? Copy it in Procreate, then paste in the other app.