How to Convert Procreate Image to 300 Dpi
StyleFrame Team6 min read
To convert a Procreate image to 300 DPI, you change the DPI tag and make sure the pixel dimensions are large enough for your print size. The DPI value is only metadata, and the pixel count is what determines quality. Divide the pixel width by 300 to get the largest print size, in inches, that will look sharp. If the file is too small, resample or upscale it. If it is already big enough, you only need to set the tag to 300 in an image editor such as Affinity Photo.
What 300 DPI Actually Means
DPI (technically PPI in a digital file) is a ratio that links pixel dimensions to physical print size:
pixels ÷ DPI = inches
A 3000 × 3000 px image is 10 × 10 inches at 300 DPI, 20 × 20 inches at 150 DPI, and 41.7 × 41.7 inches at 72 DPI. The pixels are identical in all three cases. Only the instruction to the printer changes.
This is why typing "300" into a field rarely fixes a blurry print. If you change the DPI of a 2048 × 2048 px canvas to 300 without resampling, you get a 6.83-inch square print. You don't get more detail. If your client wants that artwork at 20 inches, you're stretching the same pixels across more paper, and the edges will soften.
Pixel dimensions, print size, and DPI must agree with one another. Fix the pixels first, then set the tag.
Step 1: Work Out the Pixels You Need
Multiply the final print dimensions in inches by 300. Here are some common targets:
Large pieces such as posters are often viewed from a distance, so a printer may accept less than 300 PPI at that size. Ask the printer for their minimum before you spend time upscaling. Treat 300 as the standard for work viewed at arm's length, not a universal law.
Step 2: Check What Your Procreate Canvas Contains
Open the artwork in Procreate and check the canvas information to see its width and height in pixels and its DPI.
Compare those pixels to the table above, or divide each side by 300. Three outcomes are possible:
- Pixels meet or exceed the target. You only need to set the DPI tag. Skip to Step 3.
- Pixels fall short by a small margin. Modest resampling may hold up. Go to Step 4.
- Pixels fall far short. You need to upscale, rebuild key elements at a higher resolution, or print smaller. Go to Step 4.
A common situation is an older canvas created at 132 DPI, which was once a default option in Procreate. If that canvas is 2048 × 2048 px, it is fine for a roughly 10-inch print, but only after you set the tag and confirm the printer is happy at that size.
Copying layers from a 132 DPI canvas into a new 300 DPI canvas of the same pixel size doesn't add resolution. You've only moved the same pixels into a different container.
Also use Procreate's Actual Size command (assignable in QuickMenu) to judge sharpness at 100%. Zooming in on any raster canvas eventually reveals pixels, so that alone doesn't tell you the file is bad.
Step 3: Set the DPI to 300 Without Changing Pixels
If the pixel count is already sufficient, export the artwork and change the tag in another app, such as Affinity Photo. Verify the pixel dimensions afterward so you know whether the image was resampled.
Affinity Photo Open the exported file, use the document resize option, set the DPI to 300, and make sure resampling is off. Confirm the pixel dimensions did not change. The width and height in inches will update.
Other image editors with a resolution setting and a resample toggle work the same way.
PNG is a stripped-down file format, and it may not reliably carry print size information. Converting to PDF is a safer option for anything you're sending to a printer.
Step 4: Add Pixels When the Canvas Is Too Small
If you need more pixels, you're resampling, which means the software invents new pixel data. The results vary by artwork type.
Hard-edged, flat, or vector-like art tolerates enlargement better. Try a detail-preserving resampling method or a dedicated upscaler, and inspect at 100% on edges and fine linework.
Textured or painterly art (brush grain, paper texture, fine hatching) is harder. Enlargement can smear texture or add artifacts, so check results against the original at actual size.
If the piece is critical, rebuild it. Recreate the canvas at the proper pixel dimensions, then redraw or re-trace the key elements. For 8 × 10 in at 300 DPI, that is 2400 × 3000 px, though layer count drops as canvas size grows.
Step 5: Export Correctly From Procreate
Even with the right pixels and tag, bad exports cause soft or shifted prints:
- Format: Export as PNG for flat color without compression artifacts, TIFF or PSD for maximum flexibility, or PDF for a print-ready container. Use JPEG only if the printer requires it, and at the highest quality.
- Color profile: sRGB is the safest choice for compatibility. Procreate's default on compatible iPads can be Display P3, which looks more vivid on Apple screens but may shift when converted. Convert to the printer's requested profile as a final step.
- Delivery path: Avoid emailing or saving through iOS Photos, which can alter the file. Use AirDrop, Files, or cloud storage and send the original export.
- Flatten or not: Send a flattened version for printing, and keep the layered .procreate or PSD file as your master.
What This Means for After Effects, Premiere, and 3D Pipelines
Video and compositing tools generally work in pixels, so the DPI tag does not determine frame size. A 3000 × 3000 px Procreate file is still 3000 × 3000 px whether it is tagged 72 or 300.
DPI becomes meaningful when you hand a still to print: posters, key art, a client's packaging mockup. Conversely, if you only need Procreate art for a 1080p or 4K timeline, concentrate on pixel dimensions and color management, not the DPI field.
Common Mistakes to Avoid
- Assuming 300 in the DPI box means high quality. It only means something once the pixel count matches the print size.
- Resampling up and down repeatedly. Each pass degrades the image. Work from the original export.
- Using 72 DPI exports for print. Keep the master large, and make a smaller web version separately.
- Ignoring viewing distance. A large poster viewed from afar can look fine at lower pixel density, while a small art print seen up close needs the full 300.
- Skipping a proof. Print a small crop at actual size, or ask for a proof from the printer.
Quick Answer Checklist
- Multiply your print size in inches by 300 to get target pixels.
- Check your Procreate canvas pixels under the canvas information.
- If pixels are enough, set the DPI to 300 with resampling off.
- If pixels are short, resample, upscale, or rebuild the canvas.
- Export as TIFF, PDF, or PNG in the right color profile and send the original file.
Once you think in pixels first and DPI second, the conversion takes a couple of minutes and no longer feels like guesswork.