How to Connect Bamboo Stylus to Procreate
StyleFrame Team6 min read
To connect a Bamboo stylus to Procreate, charge the stylus, turn on Bluetooth on your iPad, and power the pen on with its lower side button. Then open Procreate's stylus or device settings, select Bamboo Sketch, Bamboo Stylus, or Wacom Stylus, and press the lower side button until the LED stays lit. Passive styluses with a rubber tip generally need no pairing and work like a finger, and typically have no pressure sensitivity.
First, check which Bamboo stylus you have
"Bamboo stylus" covers several products, and the right process depends on which one is in your hand.
- Bamboo Sketch and Bamboo Fineline (active, Bluetooth): These need pairing. They offer pressure sensitivity, palm rejection support, and a programmable side button once connected to a supported app.
- Passive Bamboo styluses: These generally have a soft rubber tip and no battery. There is typically nothing to pair. Touch the tip to the screen and it generally behaves like a finger.
If your stylus has a USB charging connector and an LED, you have an active model and the steps below apply. If it has no battery and no button, skip to the section on passive styluses.
Step-by-step: pair an active Bamboo stylus with Procreate
1. Charge and power on the stylus
Plug the USB charger into a computer or a USB power source and snap the stylus onto the magnetic connector. The LED turns off when charging finishes, which Wacom says can take up to two hours. Press the lower side button to turn the stylus on. The LED blinks blue for about two seconds.
2. Prepare your iPad
- Open Settings and turn on Bluetooth.
- On iPad, go to General > Multitasking and turn off Gestures. Wacom recommends this step.
- Confirm that your iPad model is on Wacom's compatibility list for your stylus.
You pair the stylus inside the app rather than in iPadOS Bluetooth settings.
3. Open Procreate and find the stylus setting
Open Procreate and a canvas, then tap the Actions menu. Depending on your Procreate version, the stylus option may be listed under a device or preferences section. Community walkthroughs describe tapping Device and choosing a Wacom stylus entry from the list. Menu names change between releases, so look for any item mentioning Wacom, Bamboo, or stylus connection.
4. Select your stylus and confirm the pairing
Choose Bamboo Sketch, Bamboo Stylus, or Wacom Stylus, whichever label your version shows. Procreate will search for nearby pens. Press the lower side button on the stylus. When the LED stays on, pairing is complete. Create a new canvas and test with a few strokes of varying pressure.
5. Re-pair when you return to the app
When you reopen Procreate after using another app, press the lower side button to reconnect. If you switch between Procreate, Concepts, and Bamboo Paper in the same session, expect to repeat this.
Troubleshooting common problems
Procreate doesn't find the stylus. Make sure the pen is charged and on (the LED should blink blue when you press the button). Toggle Bluetooth off and on, close Procreate completely, and reopen it. Also check that the stylus isn't still connected to another app or device.
Strokes register but there's no pressure sensitivity. The pen may be acting as a passive tip. Open the stylus settings in Procreate and confirm the Bamboo entry is selected. Then check Procreate's pressure settings and adjust the pressure curve. Test with a pressure-sensitive brush such as a technical pen or soft airbrush.
Palm touches create stray marks. Enable Procreate's touch settings that ignore finger input while the stylus is active, or use a glove. Confirm that Multitasking Gestures are off.
The side button does nothing. Shortcut behavior varies by app. In Procreate you may need to assign the button's action in the stylus settings, if your version exposes it. Don't assume the button maps to eraser or undo by default.
The connection drops mid-session. Low battery can be a cause. Charge the pen fully, remove the case if it blocks Bluetooth, and keep the stylus within a short distance of the iPad. If problems persist after a restart, update iPadOS and Procreate, then repeat the pairing.
Using a passive Bamboo stylus
If you have a passive stylus, no pairing is generally needed. It works with Procreate as a precise finger substitute. That's fine for rough thumbnails, UI-style layout sketches, and board panels where line weight doesn't matter. For inking, lettering, or any work where stroke variation is part of the design, an active stylus (or Apple Pencil on supported iPads) will serve you better.
Tune Procreate once the stylus is connected
Pairing is only half of a usable setup. Before you start boarding or concept work, spend a few minutes on these:
- Pressure curve: Adjust it so light strokes read clearly and full pressure doesn't saturate too early. Pressure sensitivity feels different between Bamboo and Apple Pencil, so don't assume your old curve transfers.
- Stabilization and smoothing: Higher streamline settings help with clean lettering and smooth vector-like curves, but add lag. Lower them for gestural sketching.
- Brush size and opacity sliders: Keep them within reach, since the side button may not control them.
- Canvas size and DPI: If the art is headed to video, set the canvas to the pixel dimensions of your target frame (for example 3840×2160 for UHD) from the start. Resizing later softens lines.
From Procreate sketch to motion pipeline
Many motion designers, animators, and VFX artists use Procreate for the stage before the timeline: style frames, storyboards, character turnarounds, matte painting studies, and texture ideas. A few export habits make the handoff to After Effects, Premiere Pro, Blender, Cinema 4D, or Nuke smoother.
- Export layered PSD when you need to separate elements in After Effects. Name layers before export so you aren't deciphering "Layer 14" at 2 a.m. Keep an eye on blend modes, since some may render differently in Photoshop-compatible apps.
- Export PNG with transparency for single elements such as a prop, a logo, or a texture card.
- Work at a high resolution and keep a clean, flattened reference alongside the layered file.
Color management deserves a check too. What looks right on the iPad may shift in After Effects if your project uses a different working space. Match color profiles before you start a long illustration.
Quick checklist
- Identify whether your Bamboo stylus is active (Bluetooth) or passive.
- Charge it, turn on the iPad's Bluetooth, and disable Multitasking Gestures.
- Open Procreate, find the stylus or device setting, and select Bamboo Sketch, Bamboo Stylus, or Wacom Stylus.
- Press the lower side button until the LED stays on.
- Test pressure, then tune the pressure curve and smoothing.
- Re-press the button to reconnect whenever you return to the app.
- Export layered PSD or PNG for the next stage of your pipeline.
If the pairing flow in your Procreate version differs from the steps above, the principle holds: the stylus pairs through the app, not through iPadOS Bluetooth settings, and the lower side button is how you confirm it.