How to Colorfill on Procreate
StyleFrame Team7 min read
The fastest way to color fill in Procreate is ColorDrop: drag the color circle from the top right into a closed shape, keep your Apple Pencil or finger on the screen, and slide left or right to set the Threshold before you lift. For repeat fills, tap Continue Filling after a drop and tap other areas. Procreate also offers Recolor (through QuickMenu), Selections → Color Fill, and Fill Layer for other situations. If a fill floods the whole canvas, the cause is almost always a gap in the line art, a Threshold set too high, or a fill landing on the wrong layer.
Method 1: ColorDrop
ColorDrop works like a paint bucket you drag into place, and it is the primary fill tool in Procreate.
- Select your color in the Colors panel.
- Drag the Colors icon (top right) into the closed shape you want to fill. Don't lift yet.
- While holding, slide left or right. The Threshold percentage appears at the top of the canvas, with a blue bar. Left fills less, right fills more.
- Lift your pencil or finger to commit.
Procreate remembers your Threshold until you change it, so if fills start behaving strangely, check this setting first.
You can also drag a swatch from a floating palette. That helps when your fill color differs from the color you are currently drawing with.
Continue Filling
After a ColorDrop, tap Continue Filling to fill other areas with simple taps. You can also tap, hold, and drag to adjust the Threshold on the fly. Tap the tick at the top, or switch to another tool such as Paint, to leave this mode.
If your iPad and Apple Pencil support hover, you can hover over the current color in the top right and double-tap the Pencil's side to start Continue Filling immediately with that color.
Method 2: Recolor
Recolor is an older fill tool that Procreate removed and later brought back. It is only available through QuickMenu, which is off by default.
To enable it: Actions → Prefs → Gesture Controls → QuickMenu, then choose how you want to invoke it.
To use it:
- Assign Recolor to one of the QuickMenu radial slots, then tap it to enter the mode.
- Pick your color in the top right.
- Tap the areas you want to fill.
- Adjust the Flood slider to control how aggressively the fill spreads.
Recolor is a good option if you prefer tapping to dragging, or if you want a dedicated fill mode with a visible slider rather than a hold-and-slide gesture.
Method 3: Selections → Color Fill
Selections can fill an area the moment you finish selecting it. This suits shapes you define by selection rather than by line art.
- Tap Selections at the top.
- Choose a selection method from the bottom tabs: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it is highlighted blue.
- Pick your color from the Colors icon.
- Make your selection. The color fills as soon as the selection completes.
Two things to know:
- Color Fill is remembered. It stays on when you leave and re-enter Selections, so turn it off when you finish, or your next selection will fill unexpectedly.
- It works on a single layer only. You cannot Color Fill onto a group of layers.
Combining a Rectangle or Ellipse selection with Feather gives you a soft-edged fill, useful for quick background washes or vignette-style framing.
Method 4: Fill Layer
Fill Layer floods an entire layer with the current color. It is the right tool for solid backgrounds or for tinting a layer with Alpha Lock on.
- Choose your color.
- Open the Layers panel.
- Tap twice on the layer you want to fill to open Layer Options.
- Tap Fill Layer.
If Alpha Lock is on for that layer, only pixels that already contain paint get recolored, and transparent areas stay untouched. That makes Fill Layer a quick way to recolor a silhouette or a flat shape without touching its edges.
Fixing common color fill problems
Most fill complaints fall into a few categories.
The fill covers the whole canvas
Check these in order:
- Is the shape actually closed? Even a tiny gap lets the color escape. Undo, zoom in, and close the gap with a brush, or use a lower Threshold.
- Is the Threshold too high? Drop the color again and slide left while holding.
- Are you filling the right layer? If your line art is on one layer and you are filling on a new empty layer, Procreate has nothing to detect, so the color floods the whole layer. Set the line art layer as the Reference layer (Layer Options → Reference), then fill on the layer beneath it. The fill will respect the lines on the reference layer.
Alpha Lock does not fix this. It only restricts painting to existing pixels, so it will not make an empty layer fill a shape.
White spots or halos along the edges
This usually happens with textured or semi-opaque brushes. The line has faint or broken pixels, and the fill stops short. Raise the Threshold a little at a time while still holding the pencil on screen. Expect some mismatch between a solid fill and grainy linework. If you need a clean result, draw the line art on a separate layer with a more opaque brush such as a monoline, and keep texture for a separate layer on top.
Color Fill won't work in Selections
If Color Fill isn't responding, check whether you have a group selected rather than a single layer. Select an individual layer and try again.
A workflow for clean flats
If you color a lot of line art, a simple layer structure avoids most problems:
- Line art layer on top, drawn with a solid, fully opaque brush and closed shapes. Set it as the Reference layer.
- Flats layer underneath, where you do your ColorDrop fills. Because the fills land on a separate layer, you can recolor or adjust them later without touching the lines.
- Shading and texture layers above the flats, clipped to them where needed.
- Background layer at the bottom, filled with Fill Layer.
Keeping fills on their own layers matters even more if the artwork is headed to motion, where each element may need to move independently.
Taking Procreate fills into a motion pipeline
Many motion designers and animators use Procreate for concept frames, character studies, and style exploration before moving into After Effects, Cinema 4D, Blender, or Nuke. Clean flat fills help here. Closed shapes with no halos, separated onto named layers, are much easier to rig, matte, and composite.
Before exporting, check that:
- Fills extend slightly under the line art, so there are no hairline gaps when layers are moved.
- Each element you want to animate sits on its own layer.
- You export in a format that preserves layers or transparency, such as layered PSD or PNG, depending on how you plan to bring it into After Effects.
Quick reference
Final tips
- Close your shapes before you fill. It is faster than troubleshooting leaks.
- Watch the Threshold percentage whenever a fill looks off.
- Use a Reference layer for line art on its own layer.
- Switch off Selections → Color Fill when you're done with it.
- Keep fills and linework on separate layers so the file stays editable and ready for animation.
Once these habits are in place, filling in Procreate takes a few seconds per shape, and the layered files you hand off to your motion pipeline are far easier to work with.