How to Clear Procreate Screen
StyleFrame Team7 min read
To clear a Procreate screen, put three fingers on the canvas and scrub them side to side. This wipes the contents of the active layer. You can also tap the layer in the Layers panel and choose Clear. If you only want the interface gone, tap four fingers on the screen for Full Screen mode. If the scrub wipes something by accident, tap the canvas with two fingers to undo it.
"Clear" means different things depending on what you're trying to do, so the sections below cover each case.
Which "clear" do you need?
Procreate has no single "clear screen" command, because the canvas is a stack of layers. Pick the case that matches your goal:
- Erase one layer's contents: three-finger scrub, or Clear in the layer menu.
- Erase only part of a layer: make a selection, then clear it.
- Start over entirely: clear or delete every layer, or begin a fresh canvas.
- Hide the interface: four-finger tap for Full Screen.
- Reset a messy workspace: reset gesture controls, pressure curve, or brushes.
Clear a layer with the three-finger scrub
This is a quick method, and it's the gesture Procreate's handbook lists for clearing a layer.
- Tap the layer you want to clear in the Layers panel so it's active.
- Place three fingers on the canvas.
- Move them left and right in a scrubbing motion, as if rubbing out a chalkboard.
The active layer empties immediately. Other layers are untouched. Make sure the right layer is selected before you scrub, because that is the most common cause of accidental wipes. Clearing a layer also doesn't remove the canvas background color. If the canvas still looks filled afterward, open the Layers panel and toggle off Background color.
Clear a layer from the Layers panel
If you'd rather not rely on gestures, or you're working on a stylus-only setup with touch gestures disabled, use the menu instead:
- Open the Layers panel.
- Tap the layer (or swipe left and use the layer options, depending on your version).
- Choose Clear.
The result is the same as the scrub. The menu is slower, but it's more deliberate, which helps when you're in the middle of a long session and don't want to risk a stray gesture.
Clear only part of a layer
For partial clears, use a selection so you don't wipe more than you meant to:
- Open Selection and choose a mode: Freehand, Rectangle, Ellipse, or Automatic.
- Define the area. Use Invert if it's easier to select what you want to keep.
- With the selection active, scrub three fingers left and right.
Only the selected area is deleted. The same approach is how you do a rough background removal. Trace around the subject you want to keep, tap Invert, then scrub to delete everything outside it. Automatic selection works well for flat or similar-colored areas. Tap the region you want gone, hold, and drag left or right to adjust the threshold, then scrub to clear.
This is useful when you're preparing isolated elements for animation. Procreate has no dedicated one-click background remover, so selections are the manual route.
Clear everything and start fresh
You have three reasonable options.
Clear each layer. Select a layer, scrub, and repeat. This keeps your layer structure, names, and blend modes intact, which is handy if you're reusing a layered template for a series of frames.
Delete the layers. If you want an empty stack, swipe left on each layer you don't need and delete it. Leave one empty layer so you have somewhere to draw.
Duplicate or create a new canvas. In the Gallery, swipe left on a canvas thumbnail and duplicate it before you wipe anything. That gives you a safe copy of the original. For a clean slate at the same size, create a new canvas with matching dimensions.
Duplicating first is the safest habit. Once you leave the Gallery or quit Procreate, the undo history is cleared and your changes are saved as permanent.
Undo and redo if you clear by mistake
Accidental scrubs happen to everyone, particularly with palm contact on a large iPad. Recovery is quick:
- Undo: tap the canvas with two fingers. A notice at the top of the interface tells you which action was reversed.
- Rapid undo: tap and hold two fingers to step back through recent actions. Lift when you reach the state you want.
- Redo: tap with three fingers, or hold three fingers to redo a run of actions.
Procreate can undo up to 250 actions. That history is only available in the current session. Returning to the Gallery or exiting the app clears the undo states. If you clear a layer and then close the canvas, there's no way back unless you have a duplicate or a backup.
If rapid undo triggers too quickly or too slowly for you, open Actions → Prefs and adjust the Rapid Undo Delay slider. One user-support answer in Procreate's community forum puts the default at 0.65 seconds.
Clear the interface, not the artwork
Sometimes "clear the screen" just means getting the UI out of the way, for example to check composition or record a screen capture.
- Four-finger tap switches to Full Screen mode. The interface slides away and you see only the canvas.
- Tap with four fingers again, or tap the Full Screen indicator in the top-left corner, to bring the interface back.
- Quick Pinch (the Pinch to Zoom gesture performed fast) snaps the canvas to fit the screen. Reverse the gesture to return to your previous view.
If you're mirroring the canvas to a second display, the Project canvas option in Prefs is designed for that. It's off by default, and there's no reason to turn it on unless you're connecting a second monitor via AirPlay or a cable.
If gestures aren't behaving
If the three-finger scrub fires when you don't expect it, or doesn't fire at all, check these:
- Gesture Controls: open Actions → Prefs → Gesture Controls. You can customize or disable multi-touch shortcuts here. To return to factory behavior, use General → Reset to defaults.
- Apple Pencil users: many artists set the one-finger tap to open QuickMenu instead of painting, which is also in Gesture Controls.
- Pressure curve: if the brush feels off after someone else used your iPad, reset it under Actions → Prefs → Edit Pressure Curve.
- Modified brushes: for default brushes, swipe left on the brush thumbnail and tap Reset (greyed out if nothing has changed). Custom brushes can't be reset this way, so re-download the originals if you need them back.
Deleting and reinstalling Procreate also resets settings, but it removes your canvases, custom brushes, and palettes. Treat it as a last resort, and back everything up first.
Where cleared Procreate frames fit in a motion pipeline
Many motion designers and animators use Procreate for storyboards, style frames, and hand-drawn elements before moving into After Effects, Blender, or Nuke. Clearing layers is a routine part of that. You wipe a layer, redraw a pose or a key, and export clean frames.
Some habits make that handoff smoother:
- Keep one element per layer so clearing one doesn't disturb another.
- Duplicate the canvas before big wipes so you always have the pre-change version.
- Export clean, isolated layers or flattened frames with transparent backgrounds when you need to composite them. Toggle off the background color first.
- Name your files in sequence so they import into your compositing app as an image sequence.
This is also where an AI motion tool can help without taking control away from you. Your Procreate drawings still start the process, and you keep your compositing workflow.
Quick reference
Final tips
Select the right layer before you scrub, duplicate the canvas before large wipes, and remember that undo history disappears when you leave the canvas. Those three habits prevent most data loss. With them, clearing a Procreate screen is a one-gesture job that doesn't put your work at risk.