How to Change Stabilizer in Procreate
StyleFrame Team7 min read
To change the stabilizer in Procreate, tap the Actions (wrench) icon, go to Prefs > Pressure & Smoothing, and move the Stabilization slider to set a global value that applies to every brush. For a single brush, open the Brush Library, tap the brush once to select it and again to open Brush Studio, then adjust the Stabilization tab. There you can change StreamLine, Stabilization, and Motion Filtering independently.
Global vs. Per-Brush Stabilization: Pick the Right Level
Procreate applies stabilization at two levels, and knowing which one you are editing saves a lot of confusion.
Global stabilization lives in the app preferences and overrides brush behavior across the board. If it is turned up, every stroke is smoothed, including with brushes that were never designed for it. This suits you if you want constant smoothing for a whole session, such as inking a full storyboard page in one consistent line quality.
Per-brush stabilization lives inside Brush Studio and affects only that brush. This is the better default for most production work, because your pencil, ink, and texture brushes need very different amounts of smoothing.
If your lines feel wrong and you can't tell why, check both. A forgotten global value stacked on top of a brush's own settings is a common cause of a pen that feels off.
How to Change Global Stabilization
- Open your canvas and tap the Actions icon (the wrench).
- Tap Prefs.
- Choose Pressure & Smoothing.
- Move the Stabilization slider anywhere from 0 to 100%.
A sensible starting point is around 10–15%. Draw a few test strokes, then nudge it up until the wobble disappears without the line feeling disconnected from your hand.
Turn it back down when you switch tasks. If your Apple Pencil suddenly feels laggy or slow to respond, leftover global stabilization is almost always the reason. Loose gesture sketches, hatching, and quick thumbnails all suffer when the app is averaging your motion in the background.
How to Change Stabilization on a Single Brush
- Tap the Brush icon to open the Brush Library.
- Tap the brush you want to adjust to select it.
- Tap it again to open Brush Studio.
- Select Stabilization from the left-hand list.
- Adjust the sliders for the mode you want.
Duplicate the brush first. Swipe the brush to the left in the library and tap Duplicate. Then edit the copy. That way your original brush remains a known-good reference, which matters when you are matching line quality across a long project or a team's shared brush set.
To undo your changes, open the brush in Brush Studio, go to the About this Brush tab at the bottom of the left-hand list, and tap Reset Brush. This restores every setting, including stabilization, to the brush's original state. It is the fastest fix when you have tweaked several sliders and lost track of what you changed.
Understanding the Three Stabilization Modes
Brush Studio doesn't give you a single "stabilizer" control. It offers three related modes, and each smooths in a different way.
StreamLine
StreamLine smooths and tightens your line while keeping the curves and turns of your stroke. It has two controls:
- Amount: Higher values give a smooth, even result. Lower or off gives more natural, less polished linework.
- Pressure: Higher values produce a longer, smoother application of pressure along the stroke. Lower or off makes pressure kick in sooner as you press.
StreamLine is the go-to for inking, calligraphy, and lettering. You can make slow, precise movements without losing the smoothness of the finished stroke, and sharp turns stay intact.
Stabilization
Stabilization takes a moving average of your stroke and draws that on the canvas. The higher the value, the more it averages out wobbles. The effect is more dramatic than StreamLine: it softens corners and pulls lines straighter, drawing the stroke toward the calculated middle between start and end.
Use it for long, confident curves and clean outlines such as vehicle silhouettes, UI shapes, or character contours. Avoid it when you want corners to stay crisp.
Motion Filtering
Motion Filtering also pulls the line toward the center of the start and end points, but it works differently. It detects unexpected bumps in your motion, big or small, and ignores them when calculating that average. In practice it filters out extreme unwanted movement, such as a jolt from a bumped arm.
Expression is a subsetting of Motion Filtering. It lets you keep more of your expressive character while still smoothing, so curves and corners can be emphasized rather than flattened.
Speed Changes the Effect
With all three modes, the effect grows as you move faster. Shaky or accidental movements get smoothed out, while slow, deliberate movements are largely preserved. This means you can lean on stabilization without it overriding intentional detail. It also means test strokes should be drawn at your real working speed, not slowly and carefully.
Recommended Starting Points by Task
These are practical starting suggestions, not fixed rules. Adjust to your hand, your stylus, and your canvas zoom.
The pattern is simple: smooth lines for finished linework, minimal smoothing for anything where energy, texture, or precision matters more than polish.
Why Motion Designers and Animators Should Care
If you use Procreate for storyboards, style frames, hand-drawn overlays, or frame-by-frame animation, stabilization directly affects consistency. A few habits help:
- Set it once per brush and save a duplicate. Consistent line quality across hundreds of frames is easier when the brush behaves the same way every session.
- Don't rely on global stabilization for animation. Heavy global smoothing can make strokes feel slightly different from frame to frame depending on how fast you draw each one, which can show up as boiling lines in a different way than you intended.
- Keep a separate sketch brush with stabilization off. Rough animation and timing drawings benefit from loose, fast strokes, while clean-up passes benefit from smoothing.
- Test at export scale. Wobble that looks fine zoomed out can be obvious once a frame is composited in After Effects or Nuke at full resolution, so check your lines at the size they will actually be seen.
Troubleshooting Common Stabilizer Problems
Your lines lag behind the pencil. Check global stabilization first, then the brush's own settings. Reduce both and test again.
Corners look rounded or mushy. Lower Stabilization, and try StreamLine or Motion Filtering with Expression instead. These keep more of the original turn.
A brush behaves differently than it did yesterday. You may have changed a global value and forgotten. If you edited the brush itself, use Reset Brush from the About this Brush tab, or revert to the duplicate you saved.
Texture or grain looks overly clean. Smoothing can strip out intended roughness. Lower the values for texture brushes specifically.
Edits won't stay on a shared brush. Duplicate the brush before editing, so you work on your own copy rather than modifying the original.
Quick Reference
- Global: Actions (wrench) > Prefs > Pressure & Smoothing > Stabilization slider (0–100%).
- Per brush: Brush Library > select brush > tap again for Brush Studio > Stabilization tab.
- Modes: StreamLine (smooths while keeping curves), Stabilization (averages and straightens), Motion Filtering (ignores sudden bumps), with Expression to preserve character.
- Start low: around 10–15% globally, then adjust.
- Protect your originals: duplicate before editing, and use Reset Brush in About this Brush to restore defaults.
- Turn it down for gesture work, texture, and sharp corners.
Once you know which level you are editing and which mode does what, changing the stabilizer in Procreate is a quick adjustment, and your linework stays predictable from the first thumbnail to the final frame.