How to Change Saturation in Procreate
StyleFrame Team7 min read
To change saturation in Procreate, select the layer, tap the Adjustments icon (the magic wand), choose Hue, Saturation, Brightness, and drag the Saturation slider. Moving it left pulls the colors toward gray, and moving it right makes them more vivid. Tap the Adjustments icon again to commit the change, or tap the canvas and choose Apply if you want to keep tweaking in the same tool.
Step-by-Step: Adjust Saturation on a Layer
- Select the layer. Adjustments act on the active layer only, so tap the layer that holds the colors you want to change. If your illustration is flattened into one layer, the adjustment hits everything on it.
- Open Adjustments. Tap the magic wand icon in the top-left corner of the interface.
- Choose Hue, Saturation, Brightness. Three sliders appear at the bottom of the screen.
- Drag the Saturation slider. Left moves toward grayscale. Right increases color strength until it reaches its limit.
- Commit. Tap the Adjustments icon again to apply the change and leave the menu. To apply and stay in the tool, tap the canvas to bring up Adjustment Actions, then tap Apply.
On older versions of Procreate, tapping another tool also committed the change, and a two-finger tap undid it. The current handbook describes the Apply flow above, so if your menu behaves differently, check which version you're running.
What the Saturation Slider Actually Does
Saturation controls color strength: how far a color sits from neutral gray. Drag the slider far enough left and the layer becomes grayscale. Push it right and colors intensify until they hit a ceiling.
It is a global operation on the layer.
The same panel has two siblings worth knowing:
- Hue rotates every color around the spectrum, so shifting hue changes what the colors are while saturation changes how strong they are.
- Brightness moves overall lightness. Saturation and brightness interact visually, so a saturation boost often needs a small brightness correction to keep the image from looking neon or flat.
A practical habit: nudge saturation in small increments, then toggle between the adjusted and original layer visibility to check you haven't clipped detail in the most colorful areas.
Change Saturation on Part of an Image
The Adjustments menu works on a whole layer, but you have several ways to restrict it.
Use a Selection
Make a selection first, then open Adjustments. Only the selected pixels on the active layer are affected.
Separate Elements Onto Layers
The easiest way to keep saturation control is to keep elements apart: background, midground, character, effects. You can then desaturate a background to push it back in space without touching the foreground. This is the same logic as splitting passes in a comp, and it pays off every time a client says "can the sky be less intense?"
Use Alpha Lock
Swipe right with two fingers on a layer to turn on Alpha Lock. Color changes then only affect pixels that already exist, leaving transparent areas untouched. It's useful for recoloring a shape without spilling outside its edges.
Change Saturation Non-Destructively
Procreate's Adjustments menu is destructive once committed: it changes the layer's pixels. If you need non-destructive flexibility, you have two options.
Duplicate Before Adjusting
Duplicate the layer, hide the original, and apply the adjustment to the copy. It's crude but reliable. Undo history helps in the moment, but a duplicated layer survives closing and reopening the file.
Use a Clipping Mask With a Blend Mode
Create a new layer directly above the one you want to change and clip it to the layer below (tap the layer and choose Clipping Mask). Then set its blend mode. Using Color mode, for instance, you can paint a new color over existing artwork while keeping the underlying values. Lower the layer opacity to control strength. Because the change lives on its own layer, you can delete it or adjust it at any time.
Be Careful With the Saturation Blend Mode
Procreate has a Saturation blend mode, and it behaves differently from what many people expect. In user forum discussions, artists report that a layer set to Saturation does not simply raise saturation. Based on those reports, the color you paint on that layer influences the saturation of what's below, but it tends to reduce saturation rather than boost it, and brightness of the painted color appears to matter as well while hue is ignored. Treat it as a desaturation tool and test it on a copy.
A related technique is to drop a desaturated color onto a layer in Saturation mode and use opacity to control how much it dulls everything beneath. Used on a layer stacked above your artwork, it acts like a rough adjustment layer, but verify the result on your own version of the app rather than assuming it will behave like a true adjustment layer.
For brushes, the Saturation blend mode on a brush stroke works more intuitively: it applies the saturation level of your chosen color to what you paint over.
Change the Saturation of a Color Before You Paint
If you want a more or less saturated color for new strokes, use the color picker rather than the Adjustments menu. Tap the color circle in the top-right corner, then pick the mode that suits you:
- Disc: drag around the wheel to choose hue, then move within the inner square to set saturation and brightness.
- Classic: use separate sliders for hue, saturation, and brightness.
- Harmony: pick colors that relate to each other on the wheel.
- Value: type exact RGB, HSB, or hex values.
- Palettes: save and reuse a set of colors so saturation stays consistent across a project.
For motion work, the Value tab is the most useful. If your brand or style frame specifies hex values, enter them directly rather than eyeballing the disc.
When Saturation Isn't Enough: Color Balance and Curves
Sometimes the problem isn't saturation at all. Two other tools in the same menu solve related issues.
Color Balance lets you shift red, green, and blue against their opposites (cyan, magenta, yellow) and target shadows, midtones, or highlights separately. Midtones are selected by default and give the most even result. If colors look dull because of a color cast, Color Balance often fixes it better than adding saturation.
Curves bends the tonal line on a graph over a histogram of the layer's colors. If artwork looks muddy or low contrast, a gentle curve can bring back life, and you can then trim saturation afterwards if needed. One illustrator notes that art made on a dark interface with bright screen settings can look flat in daylight, and Curves followed by a saturation tweak is the fix.
Common Problems and Fixes
- Nothing changes. Check that you selected the right layer and that it isn't empty or locked. Also confirm you are not looking at a different layer stacked on top.
- The whole image shifted when you wanted one element. The art was probably flattened or on a single layer. Use a selection.
- Colors look garish after boosting. Reduce saturation slightly and lower brightness, or use Curves to restore contrast.
- Grayscale won't come back. Once committed, you can't recover lost color by pushing the slider back. Undo, or revert to a duplicate.
- Colors look different elsewhere. Display settings and color profiles vary between your iPad and your computer, so judge final saturation in the environment where the work will be delivered.
Moving Procreate Art Into a Motion Pipeline
For motion designers and VFX artists, Procreate is often a source of style frames, textures, or illustrated elements. A sensible workflow is to do broad color decisions in Procreate and leave final color control to your compositing app, where changes stay editable.
Export layers separately from Procreate so your compositing app can treat each element independently.
Quick Reference
Saturation in Procreate is quick to change but permanent once committed, so work on copies or clipped layers, and save the final, editable color decisions for your compositing software.