How to Change Pressure Sensitivity Procreate
StyleFrame Team7 min read
To change pressure sensitivity in Procreate, open Actions (wrench icon) > Prefs > Pressure and Smoothing and reshape the pressure curve. Tap the line to add nodes and drag them. Raising the curve makes light touches leave stronger marks, and lowering it demands more force. For a single brush, open Brush Studio > Apple Pencil and adjust the Pressure sliders for size and opacity. If a change makes things worse, tap Reset all at the bottom of the Pressure and Smoothing screen.
Two Places Where Pressure Is Controlled
Procreate handles pressure at two levels, and mixing them up is the most common reason an adjustment seems to do nothing.
- Global pressure curve (Prefs): applies to every brush and every stroke. It maps how hard you press to how strongly the pressure response kicks in.
- Per-brush pressure (Brush Studio): decides what pressure actually affects for a given brush, such as size, opacity, or taper.
Think of the global curve as the input calibration and the brush settings as the response. If your pencil feels wrong everywhere, start with the global curve. If only one brush feels off, go to Brush Studio.
How to Change the Global Pressure Curve
- Open a canvas. The Actions menu is only reachable from inside one, though the setting applies app-wide.
- Tap the wrench icon, then Prefs.
- Tap Pressure and Smoothing.
- Find the pressure graph. The horizontal axis is how hard you press, from nothing at the left to maximum at the right. The vertical axis is how strongly that pressure affects your brushes.
- Tap the line to add a node, then drag it. Drag the end points to change the overall slope.
- Test on a scratch layer after each small change.
The default is a straight diagonal. Every change bends that relationship, so make small moves and test often.
Make Light Marks Appear Sooner
If you have to lean hard before a brush leaves a visible mark, the curve is too flat at the start. This is common when sketching with a pencil-style brush and building up tone.
Add a node near the middle and raise it slightly, or steepen the beginning of the curve. The same pressure now sits higher on the vertical axis, so the brush responds more strongly at lower force. Light touches still produce light marks, but mid-tones need far less effort.
Make the Pencil Require More Pressure
If your strokes jump to full size or full opacity too quickly, do the opposite. Pull the middle of the curve down so the response ramps up more slowly. This suits heavy-handed drawers and anyone doing delicate linework or fine hatching.
Turn Pressure Sensitivity Off
For uniform lines in lettering, technical shapes, or flat color blocking, you can neutralize pressure entirely. Drag the top-right point of the curve to the top-left corner so the line goes vertical. If it won't reach the very edge, get as close as you can. Brush thickness is then governed by the size slider rather than by how hard you press.
To undo this, drag the point back to the right so the curve is diagonal again, or use Reset all.
Reset to Default
If you've over-tweaked, scroll to the bottom of the Pressure and Smoothing screen, tap Reset all, and confirm. This resets everything on that screen, including smoothing values, so note any settings you want to keep.
Procreate's own documentation advises against touching the global curve unless you have a real reason. The stock brushes are designed around the default response, and an aggressive curve can make them behave unpredictably. Change it to fix a specific complaint, not out of habit.
Adjust Smoothing and Stabilization
The same screen has sliders at the top that control stabilization, which smooths your strokes. Higher values steady shaky lines and make curves more graceful. They also add lag between your hand and the mark, which can feel disconnected when you're sketching quickly.
A practical approach:
- Low stabilization for loose sketching, gesture drawing, and fast thumbnails.
- Moderate stabilization for clean inking and long, confident curves.
- High stabilization for precise vector-like shapes where you're willing to draw slowly.
These sliders apply to all brushes.
Change Pressure for a Single Brush
When one brush feels wrong, leave the global curve alone and edit the brush.
- Open the Brush Library and tap a brush to open Brush Studio. To experiment safely, duplicate it first.
- Select Apple Pencil in the sidebar.
- In the Pressure section, adjust the sliders. The Size slider controls how much pressure changes the stroke width. The Opacity slider controls how much pressure changes transparency.
- Test in the drawing pad at the bottom of the screen.
Sliding a value into negative territory inverts the behavior: light pressure gives a thicker or more opaque mark, and heavy pressure gives a thinner or fainter one. That's useful for specialized effects but confusing if it's set by accident.
Taper Settings
Right alongside pressure, the Taper settings control how strokes thin out at the start and end. If lines stay thick even when you ease off the pressure, taper settings are a frequent culprit. Community advice for this exact complaint is to disable or reduce softness and size taper on the brush, then retest. Only after that should you consider adjusting the global curve.
Third-Party Styluses
Procreate's pressure and tilt controls need a pressure-capable stylus. A cheap capacitive pen can draw, but it won't deliver pressure data. For supported third-party styluses, go to Actions > Prefs > Connect third-party stylus and follow the Bluetooth pairing steps.
For Apple Pencil, make sure Bluetooth is on and the pencil is paired to the iPad. Newer models pair when you attach them to the side of the iPad, and a dialog confirms the connection and battery level.
Troubleshooting Pressure Problems
Pressure only seems to work in one direction (strokes get thicker but never thinner). Check the brush's taper and size settings first, then look at the curve. A curve that saturates too early will make the response hit its maximum with moderate pressure and stay there.
Everything feels too sensitive or too stiff. Reset all, then apply one small adjustment instead of several. Compounded changes are hard to diagnose.
Fast strokes feel inconsistent. Fast strokes can respond differently than slow ones. Lower stabilization if you suspect lag, and try a gentler curve rather than a dramatic one.
Nothing changes when you edit the curve. Confirm that the brush in use actually has pressure assigned to size or opacity. If the brush's pressure sliders are at zero, no global curve will make it respond.
Only one brush misbehaves. That points to Brush Studio, not Prefs. Duplicate the brush and edit the copy.
Where This Fits in a Motion or VFX Pipeline
Many motion designers and VFX artists use Procreate for the pre-production and asset-making end of a job: style frames, storyboard panels, hand-drawn textures, matte paintings, rough character designs, and ink or paint elements to composite later. Consistent pressure behavior matters here. If you're producing a set of boards or a library of hand-drawn elements, you want line weight and opacity to feel the same from piece to piece, which is a reason to fix your curve once and leave it, or to save a duplicated brush with the response you want.
Once you have the artwork, it typically moves on: flattened or layered PNG and PSD exports go into After Effects, Photoshop, Nuke, or Blender as textures, mattes, or animation reference.
Quick Reference
Final Advice
Make one change at a time, test on a scratch layer, and keep the global curve close to default unless you have a clear problem. Use Brush Studio for brush-specific behavior, since it's less risky than altering the global curve. If your drawing is feeding a larger animation or compositing pipeline, settle on a response you like early and keep it consistent across the whole project.