How to Change Pen Pressure in Procreate
StyleFrame Team6 min read
To change pen pressure in Procreate, tap the Actions (wrench) icon, open Prefs, and choose Pressure and Smoothing (older versions label it Edit Pressure Curve). Drag the graph's curve to set how hard you must press for a stroke to register. Brush-specific response lives in a second place: Brush Studio, under Apple Pencil, where you set how pressure affects size, opacity, and taper for each brush. Tap Reset all in the Pressure and Smoothing menu if you want to undo your changes.
Two Places Pressure Is Controlled
Most confusion about pressure in Procreate comes from the fact that two separate systems shape what you see on the canvas:
- The global pressure curve sits in Actions → Prefs. It remaps the raw pressure your Apple Pencil (or another supported stylus) sends, and it affects every brush.
- Per-brush pressure settings sit in Brush Studio under Apple Pencil. They decide what each brush does with that pressure: change size, change opacity, taper at the ends, and so on.
Think of the global curve as your hand calibration and the brush settings as the character of each tool. If one brush feels wrong, fix that brush first. If every brush feels too heavy or too light, adjust the global curve.
How to Edit the Global Pressure Curve
- Tap the Actions icon (wrench) at the top left of the canvas.
- Open Prefs.
- Tap Pressure and Smoothing (or Edit Pressure Curve in older builds).
- Drag the curve on the graph, or tap the line to add nodes and shape it.
- Draw a test stroke on a blank canvas, starting light, pressing hard, then easing off.
Reading the graph
The horizontal axis is the physical pressure from your pencil, from none on the far left to maximum on the far right. The vertical axis is the effect Procreate applies to your brushes, from none at the bottom to full at the top. The default is a straight diagonal: effect rises evenly with pressure.
- Pull the curve upward (bowing it above the diagonal) and brushes respond more strongly to lighter pressure. Marks get darker or thicker with less effort.
- Pull the curve downward and you need to press harder to get the same result. This helps if you tend to press heavily and your lines go thick too quickly.
- Make the start steeper if light touches barely register. One tutorial author finds that the angle at the beginning of the curve changes the feel more than any other part, especially for pencil-style sketching where you want mid-gray tones without leaning on the screen.
- Add nodes for an S-shape if you want a gentle response at low pressure and a more dramatic ramp at higher pressure.
Procreate's own documentation cautions against changing the global curve unless you have a reason, because the stock brushes are tuned for the default and a drastic curve can produce unexpected results. Make small adjustments, test, and only then go further.
Smoothing and Stabilization
The same Pressure and Smoothing screen has sliders at the top that control stabilization for all brushes. Raising them smooths wobble in your strokes, which helps with long, clean contours and lettering. The tradeoff is lag: heavy stabilization can make fast gestural sketching feel disconnected from your hand. Keep it low for loose animation roughs and raise it for clean-up passes.
How to Change Pressure Response Per Brush
Open the Brush Library, tap a brush to open Brush Studio, and select Apple Pencil in the left-hand list. The Pressure section offers sliders that tie pressure to different qualities of the stroke.
Size and opacity
Raising the Size slider makes the stroke thicken as you press harder, much like a soft-tipped marker or brush. Pushing it into negative values reverses the behavior, so light pressure gives thick lines and heavy pressure gives thin ones. The Opacity slider works the same way for transparency, which suits layered shading and pencil-style buildup. Many artists leave opacity alone and rely on size for line variation, but that is a matter of style.
Taper
The Taper section controls how a stroke thins at its beginning and end. You can link or unlink the head and tail. A longer distance before the first node produces a smoother, more gradual transition. This matters for ink-style linework, where the line should swell and then vanish naturally.
If thickness only goes one way
A common complaint is that a line gets thicker with pressure but won't thin out again when you lighten up. Before blaming the hardware, check the brush's Taper and Softness-related settings. Forum advice for this problem includes disabling size taper or softness on that brush and nudging the bottom node of the global curve a little at a time. Fast strokes can also expose differences between an iPad and a dedicated pen display, so test slow and fast.
Starting Points for Common Tasks
These are suggestions to experiment from, not fixed values:
- Rough animation sketches: Keep the default curve or lift the start slightly so light strokes register. Use low stabilization.
- Clean line art for keyframes: Add moderate stabilization, link the taper ends, and use a brush with size tied to pressure for a controlled swell.
- Pencil-style shading and texture passes: Steepen the start of the curve so mid-tones build without hard pressing.
- Heavy-handed drawers: Pull the curve down in the middle so you get more range before hitting maximum thickness.
Adjust one thing at a time. If you change both the global curve and the brush sliders in the same session, you won't know which one caused the new feel.
Troubleshooting Pressure That Isn't Working
- No pressure at all: Pressure and tilt require a pressure-capable stylus that Procreate supports. A generic capacitive stylus won't send pressure data, regardless of settings.
- Apple Pencil not responding: Confirm Bluetooth is enabled in Control Center and that the pencil is paired. Procreate's help center covers connection steps for supported Apple Pencil models.
- Odd results after experimenting: Go to Actions → Prefs → Pressure and Smoothing, scroll to the bottom, tap Reset all, and confirm. This restores the defaults.
- One brush only behaves oddly: Duplicate the brush, then compare its Apple Pencil settings against a stock brush that feels right.
Where Procreate Fits in a Motion Pipeline
For motion designers, animators, and VFX artists, Procreate is usually a front-end tool: boarding, character and style exploration, hand-drawn keyframes, texture and brush work, and paintovers. Getting pressure dialed in matters because those drawings often become the source material for later stages. Inconsistent line weight across a set of frames reads as flicker once the artwork is animated or composited.
You can export your Procreate drawings into a conventional compositing workflow. Keep a consistent brush and curve across an entire sequence, and avoid changing pressure settings midway through a set of related frames.
The takeaway: the time you spend tuning pressure curves in Procreate isn't wasted on a stage that gets replaced. Cleaner, more deliberate source drawings give any downstream tool, AI-assisted or not, better material to follow.
Quick Reference
Make small changes, test with the same three-part stroke each time (light, heavy, light), and settle on a curve that feels natural. Once it does, you can stop thinking about it and focus on the drawing.