How to Change Opacity of Layer in Procreate
StyleFrame Team7 min read
To change the opacity of a layer in Procreate, open the Layers panel, tap the "N" on the right side of the layer, and drag the Opacity slider. The "N" is the default letter shown there, and it may differ if you've changed the layer's setting. For a faster, gesture-based option, select the layer and use Adjustments > Opacity, then slide a finger left or right on the canvas.
Quick method: the Layers panel opacity slider
This method is non-destructive because you can return and change the value at any time.
- Tap the Layers icon in the top right to open the panel.
- Find the layer you want to adjust. Tap the small letter (or letters) to the right of the layer name. By default this is "N."
- A menu opens with an Opacity slider. Drag the slider left to make the layer more transparent, or right to make it more solid.
- Tap outside the menu to close it.
The percentage appears as you drag, so you can land on a specific value. If you need precision, such as exactly 35%, drag slowly and check the readout. Because the value lives on the layer itself, you can reopen the menu later and change it again without affecting your paint.
If you're used to After Effects, this is the closest equivalent of tapping T on a layer and scrubbing the Opacity property. The main difference is that Procreate gives you no keyframe stopwatch, so the value is static across the canvas.
Alternative method: Adjustments > Opacity
Procreate also has an Opacity option in the Adjustments menu. This is a touch-driven mode that works on the active layer.
- Select the layer you want to change.
- Tap Adjustments, then choose Opacity.
- A blue bar labelled "Slide to adjust" appears at the top of the screen and displays the layer's current opacity, starting at 100%.
- Slide a finger left on the canvas to reduce opacity, or right to increase it.
- To commit, tap the Adjustments icon again or tap another tool. To exit without applying, tap Cancel.
The buttons at the bottom of the interface let you cancel, undo the last change, redo it, or reset everything while staying in the mode. This approach is handy when you want to judge the result visually against the rest of the artwork as you drag, rather than reading a slider.
Treat this as a quicker, more tactile version of the same change. If you want to keep adjusting later in the project, the Layers panel slider is the better habit, since you can reopen it at any time.
Changing the opacity of a selection
Sometimes you don't want the whole layer to fade, just part of it. Procreate supports this, but it behaves differently from the layer slider.
- Open the Selection tool and pick your preferred method.
- Make your selection on the canvas.
- Open the Layers panel and tap the layer that holds the paint with two fingers at the same time.
- Slide a finger left on the canvas to reduce the opacity of the selected area, or right to increase it.
The important detail is that this is a destructive action. When you exit the mode, the change is applied to the pixels. You can undo immediately, but you can't return later and adjust the value like a layer slider. Each use is final.
If you expect to revisit the fade, a more flexible workflow is to cut the selected area onto its own layer (for example, by copying the selection to a new layer) and then use the normal layer opacity slider on that layer. That costs you one extra layer but keeps your options open.
Layer opacity vs. brush opacity
New users often confuse two separate controls.
- Layer opacity controls how visible an entire layer is. It affects everything already painted on that layer and anything you paint afterward.
- Brush opacity controls how strong each stroke is as you paint. It's the lower slider on the Sidebar: drag up to increase, down to decrease.
If a stroke looks too faint even though your layer is at 100%, check the brush opacity slider. Many brushes also respond to Apple Pencil pressure, so a light touch can produce transparent marks even when the slider is at maximum. In that case, the cause is pressure sensitivity rather than the layer setting, and you may need to look into your pressure settings.
A practical rule: use brush opacity while building up tone, and use layer opacity when you want to balance one element against others.
Troubleshooting common problems
The slider moves but nothing changes. Make sure you've selected the layer you actually mean to change. Procreate adjusts the active layer, and it's easy to tap a neighboring one.
A layer looks faded even at 100%. Check the blend mode. Modes such as Multiply, Overlay, or Soft Light change how the layer interacts with those beneath it, which can look like a transparency issue. Also check whether the layer is inside a group with its own opacity setting.
Clipped content behaves oddly. A layer set as a clipping mask only shows where the layer beneath it has pixels. If the base layer has low opacity, the clipped content is affected too. Adjusting the base layer changes how everything attached to it reads.
Opacity seems to stack. Opacity is multiplicative across groups and layers. A layer at 50% inside a group at 50% will appear at roughly 25% visibility. This is the same logic you'll know from nested precomps in After Effects.
Using layer opacity in a motion pipeline
If you work in After Effects, Premiere Pro, or a compositing tool like Nuke, Procreate is most often a source of concept art, style frames, textures, or hand-drawn elements. Opacity handling matters when those layers leave the iPad.
- Export as PSD when you want to keep layers separate. Spot-check the result in the receiving app, since opacity and blend modes can render slightly differently between apps.
- Export flattened PNG or JPEG when you only need a reference or a final still. Any opacity you set is baked into the image.
- Export transparent PNGs for elements you plan to animate. Hide the background layer first so that transparency survives.
- Animate opacity in your motion tool, not in Procreate. Procreate's opacity value is static. If an element needs to fade, export it at full opacity on its own layer and keyframe the Opacity property in After Effects, where you get proper easing and graph control.
This split of responsibilities keeps your source artwork clean. Use Procreate for the look, and use your compositing application for timing.
Where Styleframe fits when your Procreate art becomes motion
Procreate is a strong place to design a frame: you paint it, tune layer opacities until the values feel right, and export a still. The harder question is how to carry that look into moving imagery without losing control.
When preparing Procreate art as a reference, consider exporting a version with your final opacity values flattened, so the reference matches the look you intend. If you need clean elements, export separate transparent PNGs from individual layers as well.
Quick reference
Final thoughts
For most work, the Layers panel slider is the right tool: tap the "N," drag the Opacity slider, and you can come back to refine it at any point. Use the Adjustments option for quick, visual tweaks, and reserve selection-based opacity for cases where you accept a permanent change. Keep brush opacity and layer opacity separate in your head, check blend modes and groups when things look off, and handle any fades over time in your motion software rather than in Procreate.