How to Change Opacity in Procreate Pocket
StyleFrame Team7 min read
In Procreate Pocket, you change brush opacity with the bottom slider on the left side of the canvas. You change layer opacity by opening Layers, tapping the letter next to the layer name (usually "N"), and dragging the opacity slider. To fade a layer quickly, tap it with two fingers in the Layers panel and slide left or right. If the bottom slider controls pressure instead of opacity, tap and hold the slider button until you feel a haptic tap or see it pulse, which swaps it back to opacity.
What Opacity Controls in Procreate Pocket
Opacity in Procreate is how visible a pixel, or a group of pixels, is. At 100% it is fully visible, and at 50% it is half see-through. The app lets you control it in three places:
- The brush, which affects each stroke as you paint.
- The layer, which affects everything on that layer.
- A selection, which affects only the isolated area of a layer.
These behave differently, and the difference matters if you're used to After Effects. Brush opacity bakes into the pixels as you paint. Layer opacity is a live, repeatable setting. Selection opacity is applied once and can't be revisited.
Method 1: Change Brush Opacity
Use this when you want soft, buildable strokes or glazes rather than a hard, solid line.
- Select a brush (using the paint, smudge, or erase tool).
- Find the two sliders on the left side of the interface. The top one controls brush size, and the bottom one controls opacity or pressure.
- Drag the bottom slider up to increase opacity and down to decrease it.
Make fine adjustments
Hold the slider, then drag your finger sideways away from it without lifting. While you're off to the side, drag up or down. The farther your finger is from the slider, the smaller the increments. This is the fastest way to land on a specific value like 35% rather than just "somewhere around a third."
If the slider changes pressure instead of opacity
This is the most common Pocket-specific stumbling block. On an iPhone with 3D Touch, the bottom slider alters opacity. On an iPhone without it, the slider defaults to controlling pressure and its effect on the brush. To swap it:
- Tap and hold the slider button.
- Wait for the haptic tap. If your phone doesn't support haptics, the button visibly pulses instead.
- Check that the slider now adjusts opacity, then set your value.
If your opacity is maxed out and strokes still look too transparent, pressure sensitivity is probably the cause. Many brushes respond to pressure as well as to the opacity setting.
Method 2: Change Layer Opacity
Layer opacity is the one you'll use most for compositing-style work: fading a shadow layer, knocking back a sketch, or stacking translucent washes. It is non-destructive, because you can come back and change it as many times as you like.
Option A: The layer menu
- Tap the expand (ellipsis) icon in the top left to open the expanded tools.
- Tap Layers.
- Tap the small letter to the right of the layer name. It's "N" by default, which is the layer's blend mode letter.
- Drag the opacity slider that appears. Left lowers opacity and right raises it.
The same panel holds the blend modes, so you can set opacity and blend mode in one visit. That's useful when you're building multiply shadows or screen glows.
Option B: The two-finger gesture
- Open the Layers panel.
- Tap the layer with two fingers at the same time. Index and middle fingers of one hand work well.
- Slide a finger left on the canvas to reduce opacity, or right to increase it.
- Lift your finger to set the value.
Because the gesture happens over the canvas, you can watch the artwork change as you slide. That is a better way to judge a ghosted layer or a faded underdrawing than a number in a menu.
Adjust one layer at a time, since the gesture and slider both target the single active layer.
Method 3: Change Opacity on a Selection
Sometimes you want to fade only part of a layer: one shape, one region, one character on a shared layer.
- Open Selections and choose a method at the bottom (Automatic, Freehand, and so on).
- Make your selection.
- Open Layers.
- Tap the layer containing the paint with two fingers at the same time.
- Slide left on the canvas to reduce the opacity of the selected area, or right to increase it.
The catch: it's destructive
When you exit this mode, the change is applied to the pixels. You can undo it immediately, but you can't reopen and tweak it later the way you can with the layer slider. Every application is final.
If you might want to change your mind, avoid this method. Copy the selected area to its own layer (or cut it to a new one), then use layer opacity on that layer instead. You get the same visual result with an adjustable setting.
One gotcha: opening the layer menu and using the regular opacity slider while a selection is active still changes the whole layer. The selection-only behavior comes from the two-finger tap on the layer. If your two-finger tap triggers an undo instead, check your gesture settings, since two-finger tap can be assigned to undo.
Which Method Should You Use?
Pro Tips for Cleaner Opacity Work
Use clipping masks. Painting on a layer clipped to the layer below keeps your strokes inside the base shape, so you can vary brush opacity without spilling over the edges.
Separate layers by intent. Put shadows, highlights, and color on separate layers rather than relying on brush opacity alone. Layer opacity is far easier to revise later than baked-in strokes.
Pair opacity with blend modes. A multiply layer at 40% and a normal layer at 40% look very different. Set both in the same layer menu.
Name your layers. On a phone-sized screen, a stack of eight layers called "Layer 14" gets confusing quickly. Naming layers saves time when you're hunting for the one whose opacity you need to change.
Troubleshooting Common Opacity Problems
- The slider doesn't change opacity. It's likely set to pressure. Tap and hold the slider button to swap modes.
- The whole layer faded, not my selection. Use the two-finger tap on the layer rather than the layer menu slider.
- Strokes look too transparent at 100%. Check the brush's pressure behavior and the layer's own opacity, which also affects what you see.
- I can't undo my selection fade later. Selection opacity is destructive once applied. Rebuild it on a separate layer if you need flexibility.
- Two-finger tap undoes my work. The gesture is mapped to undo in your settings. Adjust the gesture settings, or use the layer menu slider for whole-layer changes.
Carrying Procreate Opacity Into a Motion Pipeline
Some motion designers and animators use Procreate Pocket for quick concepts, style frames, and storyboards on the go. The opacity decisions you make there can carry over to the motion work. Layers kept separate and set with layer opacity are easier to bring into a compositing app such as After Effects. Selection-based fades and heavily baked brush opacity don't translate that way, so it pays to build with separable layers from the start.
Once the artwork moves into a motion workflow, is one tool you could look at.
FAQ
Can I change opacity on a single stroke after painting it? No. Brush opacity is set before you paint. To make a stroke adjustable afterward, paint it on its own layer and change that layer's opacity.
What is the fastest way to change layer opacity in Procreate Pocket? The two-finger tap on a layer in the Layers panel, then a slide on the canvas. Opening the layer menu through the "N" is the more precise alternative.
Why is the "N" next to my layer? It is the layer's blend mode letter, and it reads "N" by default. Tapping it opens both the blend mode list and the opacity slider.
Does opacity changes on a layer damage the artwork? No. Layer opacity is non-destructive and can be changed repeatedly. Only the selection-based method commits changes permanently once applied.