How to Change Opacity in Procreate
StyleFrame Team7 min read
To change opacity in Procreate, use the lower slider in the Sidebar for brush opacity, or open the Layers panel and tap the letter next to a layer's name (usually "N") to get a layer opacity slider. For a selection or the contents of a layer, tap the layer with two fingers and slide left or right on the canvas. The Layers slider is non-destructive and can be changed later, while the two-finger method is applied permanently once you exit the adjustment.
For motion designers and compositors, the distinction matters. It decides whether you hand off a flexible layered file to After Effects or a flattened one you can't adjust.
What opacity means in Procreate
Opacity describes how visible pixels are. At 100%, they are fully solid. At 50%, they are half see-through. Procreate lets you control this in three places:
- Brush opacity: how transparent new strokes are as you paint.
- Layer opacity: how transparent an entire layer is.
- Selection or content opacity: how transparent the pixels inside a selection, or on a layer, are.
All three affect what you see on the canvas, but they behave very differently when you come back to edit. Brush opacity applies as you paint. Layer opacity is a live property. Selection opacity bakes the change into the pixels.
How to change brush opacity
Brush opacity is the quickest to adjust, and you do it before you paint.
- Select the brush you want to use.
- Find the two sliders on the Sidebar. The upper one controls brush size, and the lower one controls opacity.
- Drag the lower slider up to make strokes more opaque, or down to make them more transparent.
Each stroke then lays down paint at that opacity. This is useful for building up soft shading, glazing color, or sketching lightly before committing to a final line.
When brush opacity seems wrong
If the slider is at maximum but your strokes still look faint, the likely cause is pressure sensitivity. Many Procreate brushes tie opacity to Apple Pencil pressure, so a light touch gives a paler stroke regardless of the slider. Check your Apple Pencil pressure settings before assuming something is broken.
How to change layer opacity
Layer opacity is the method most artists should reach for by default, because it can be undone at any point.
- Tap Layers in the top-right corner to open the panel.
- Tap the small letter or letters to the right of the layer name. This shows "N" for Normal blend mode unless you've changed it.
- Use the opacity slider directly beneath it to set the value you want.
You can come back later and move the slider again, including back to 100%, and the original artwork is untouched. That is why it is described as non-destructive.
This is also the same panel where you pick blend modes such as Multiply, Screen, or Overlay. If you're used to After Effects layers, think of it as the combined blend mode and opacity controls for a layer.
Layer opacity and clipping masks
Clipping masks interact neatly with opacity. If you clip a layer to the one beneath it, your strokes stay inside the shape of the base layer. This lets you build shading, texture, or color adjustments on a separate layer without risking the base art.
How to change opacity of a selection or layer contents
The third method is the gesture-based approach, and it is the one that most often causes confusion.
- If you want to affect only part of the artwork, open Selections, pick a selection method, and make your selection.
- Open Layers and find the layer containing the artwork.
- Tap that layer with two fingers at once.
- Slide a finger left on the canvas to decrease opacity, or right to increase it.
- Exit the adjustment to apply the change.
Without an active selection, this adjusts the whole layer's pixels. With a selection, it affects only the selected area.
Why this method is destructive
Once you exit this mode, the change is baked in. You can undo right away, but you can't return later and nudge the value. Whatever opacity you landed on effectively becomes the new 100% for those pixels. If you apply it twice, the second change compounds on the first.
For that reason, use this approach when you really do want to alter specific pixels, such as fading just one region of a layer. If you only want a layer to look lighter, use the Layers panel slider instead.
Using QuickMenu for faster opacity control
If you change opacity constantly, you can add the opacity action to QuickMenu so it's available with a touch-and-hold gesture on the canvas. There's one catch. The QuickMenu action labeled "Layer Opacity" behaves like the destructive opacity adjustment from the two-finger method, not like the non-destructive slider in the Layers panel. With an active selection, it changes only the selection.
So QuickMenu is great for speed, but treat it as a pixel-level edit and not as a reversible layer property. If you want something you can come back to, keep using the Layers slider.
Troubleshooting: opacity not responding
A few common problems come up repeatedly.
- The slider won't move when you drag it. In the two-finger method, the blue bar at the top is a readout, not a control. Drag left and right on the canvas itself.
- Two-finger tap does nothing. Try a hard reboot of the iPad, which Procreate community members commonly suggest for this problem.
- You can't find opacity in the Adjustments menu. Current versions don't have it there. Use the Layers panel, the two-finger gesture, or QuickMenu.
- Strokes are faint even at full opacity. Check Apple Pencil pressure settings, as covered earlier.
- You can't get back to the original look. If you used a destructive method, undo immediately. Otherwise, you'll need to repaint or restore from an earlier state.
Different Procreate versions have shuffled some of these controls over time, so if a forum answer doesn't match your screen, check that it refers to a recent release.
Choosing the right method
When in doubt, split your artwork into more layers and use the layer slider. It costs a little organization but saves hours when a client asks you to lighten something three revisions later.
Procreate opacity in a motion pipeline
Many motion designers and animators use Procreate for concept frames, illustrated elements, textures, and hand-drawn passes that later go into After Effects, Premiere Pro, Blender, Cinema 4D, or Nuke. A few habits make that handoff cleaner.
- Keep opacity on layers, not baked into pixels. Baked-in opacity can't be changed once it's in the file.
- Separate elements that will animate. Put anything that will fade, move, or be revealed on its own layer, and avoid using the destructive gesture on those layers.
- Export with your compositing needs in mind. Check how Procreate's blend modes translate in your target app, because they may not match exactly. Test a small export before delivering a full set.
- Use transparent backgrounds for elements. If you plan to composite a drawing over footage, hide the background color layer and export in a format that preserves alpha.
Quick recap
- Brush opacity: use the lower Sidebar slider before you paint.
- Layer opacity: tap the "N" in the Layers panel and use the slider. It is non-destructive.
- Selection or content opacity: tap the layer with two fingers and swipe on the canvas. It is destructive.
- QuickMenu's opacity action acts like the destructive method, not the layer slider.
- If something isn't responding, drag on the canvas rather than the readout, check pressure settings, and restart the device.
Learn the difference between the reversible and permanent methods, and opacity in Procreate stops being a source of surprises. It also leaves you with cleaner layered files to take into the rest of your motion workflow.