How to Change Color of Entire Layer Procreate
StyleFrame Team7 min read
To change the color of an entire layer in Procreate, tap the layer, turn on Alpha Lock, choose your color, then tap the layer again and select Fill Layer. Alpha Lock keeps the original transparency, so only the existing pixels are recolored and the edges stay clean. For a non-destructive result, put a new layer above, set it as a Clipping Mask, and fill it with the new color. For tonal shifts instead of a flat color, use Adjustments → Hue, Saturation, Brightness on that layer.
Which Method Should You Use?
Pick based on what you want the layer to look like afterward:
The main trap for new users is reaching for tools that act on the whole canvas or on a single contiguous shape. Selections are slow and often leave fringed edges, and ColorDrop only fills the area you drop it on. The methods below act on the layer as a whole.
Method 1: Alpha Lock + Fill Layer
This is the fastest route to a flat, uniform recolor.
- Tap the layer in the Layers panel to open its menu.
- Tap Alpha Lock. A checkerboard pattern appears behind the layer thumbnail. You can also swipe right on the layer with two fingers.
- Choose your new color in the color picker.
- Tap the layer again and select Fill Layer.
Every pixel with opacity on that layer takes the new color, and transparent areas stay transparent. Anti-aliased edges and soft strokes keep their original alpha, which is why this approach avoids the jagged halos that manual selections produce.
You can also leave the fill out and simply paint over the layer with a large brush. With Alpha Lock on, only pixels that already exist accept paint, so you can scribble across the whole canvas without spilling onto empty space.
Remember to switch Alpha Lock off afterward. If you forget, later brushwork on that layer will behave strangely and you may wonder why new strokes are not appearing.
Don't use Fill Layer without Alpha Lock. On an unlocked layer, it floods the entire canvas with the color, including the transparent areas.
Method 2: Clipping Mask Recolor (Non-Destructive)
If you want to experiment with colors or keep the original intact, recolor on a separate layer instead of changing the pixels.
- Create a new layer directly above the layer you want to change.
- Tap the new layer and choose Clipping Mask. It will now only show where the layer below has content.
- Pick a color and fill the clipped layer (drag the color from the color dot onto it, or use Fill Layer).
The original layer is untouched underneath. You can swap the color, adjust the opacity, hide the clipped layer to see the original, or merge down when you're satisfied.
Using blend modes for tinted results
A flat fill on a Normal blend mode replaces all the color information. If you want to preserve the lighting and texture of the artwork underneath, change the clipped layer's blend mode:
- Color applies the new hue and saturation while keeping the underlying brightness values. This works well for painted or shaded artwork.
- Multiply darkens and tints, useful for shifting light areas toward a new color.
- Overlay or Soft Light gives a subtler color push.
One caveat: pure black and pure white have no hue to replace. A Color-mode layer over solid black lettering will stay black. For black-to-pink or black-to-white changes, use a Normal-mode clipped fill or Alpha Lock.
Method 3: Adjustments for Hue, Saturation, and Brightness
When your layer contains multiple colors and you want to move them all together, use the Adjustments menu (the magic wand icon).
- Select the layer you want to change.
- Tap Adjustments, then Hue, Saturation, Brightness.
- Make sure the adjustment is applied to Layer rather than Pencil, so it affects the whole layer.
- Drag along the screen or use the sliders to shift the values.
This approach preserves the relationships between colors, so a brown-and-tan illustration can become green-and-sage in one move. It is the right choice for alternate colorways of the same piece.
Other useful adjustments on the same menu:
- Color Balance lets you shift the colors of the layer further.
- Curves controls contrast and brightness, which helps when a recolor looks flat or muddy.
- Invert flips colors, which is a quick way to turn a black drawing white.
A limitation to keep in mind: hue shifting does nothing for neutral colors. If your artwork is pure black, shifting hue will not turn it pink because there is no hue to rotate. Use Alpha Lock or a clipped fill for that case.
Method 4: ColorDrop, and When It Falls Short
ColorDrop is Procreate's drag-and-drop fill. Drag the color from the color dot at the top right onto the canvas and release. Don't pause on the dot before dragging, or it may swap to your previous color.
If you keep your finger or Apple Pencil down after dropping, you can slide left or right to adjust the fill threshold. That setting controls the intensity and amount of coverage of the color you just dropped.
ColorDrop is good for fixing individual shapes. It is not a whole-layer tool. If a layer has dozens of separate letters or objects, you would need to drop color into each one. For entire layers, go back to Alpha Lock and Fill Layer.
Troubleshooting Common Problems
- The whole canvas turned one color. You filled an unlocked layer. Undo, enable Alpha Lock, and fill again.
- Edges look rough or have a color halo. This usually comes from a selection-based recolor. Use Alpha Lock, which keeps the original edge transparency.
- The color did not change on a black or white layer. Hue adjustments and Color blend mode cannot recolor pure neutrals. Use a Normal-mode fill.
- New strokes will not draw outside the artwork. Alpha Lock is still on. Turn it off from the layer menu.
- The color looks different from the one you picked. Check the blend mode and opacity of the layer, and whether any adjustment layers or overlays sit above it.
- Layers are in a group. Apply changes to individual layers, or duplicate and merge the group first if you need to recolor it as one piece.
A habit worth building: keep separate elements on separate layers from the start. Recoloring a lettering layer, a background, and a character independently is far easier than untangling one flattened image.
Taking Recolored Layers Into a Motion Pipeline
For motion designers, Procreate often serves as the source of hand-drawn elements: lettering, textures, character art, or backgrounds that end up in After Effects, Premiere Pro, or Nuke. A few habits make that handoff smoother:
- Keep layers separate so you can hand off individual elements with clean transparency.
- Do final color decisions late. If a client may change a palette, leave the elements flat and white or neutral and tint them later in compositing.
- Keep a clipped-color version as a reference. A Procreate file with the clipping-mask colorways is a quick way to show alternate palettes to a client before committing.
FAQ
How do I change a layer's color without affecting transparency? Turn on Alpha Lock for that layer, then use Fill Layer or paint over it. Only existing pixels will change.
How do I turn a black drawing white? Use Alpha Lock with white selected and tap Fill Layer, or apply Adjustments → Invert to the layer.
Can I undo a recolor later? Yes, if you use a clipping mask layer. Hide or delete that layer to return to the original, as long as you haven't merged it down.
Why doesn't Hue adjustment change my black lines? Black has no hue, so rotating hue has nothing to act on. Use a flat fill instead.