How to Change a Single Color in Procreate
StyleFrame Team7 min read
To change a single color in Procreate, put the artwork on its own layer, then use Recolor from the Quick Menu. Move its crosshair onto the color you want to replace, then pick a new color from the color wheel. If Recolor spills into neighboring areas, drag a color from the top-right dot with ColorDrop, or select the color with the Selection tool and fill it. Each method trades speed against edge quality, so the right one depends on how clean your linework and anti-aliasing are.
Which method should you use?
Whichever you choose, keep the element you're recoloring on its own layer. Every method below gets easier and cleaner when it can't touch anything else.
Method 1: Recolor (Quick Menu)
Recolor is the fastest way to swap one color. It works like a live flood fill that follows your color wheel.
- Assign Recolor to the Quick Menu. Open Actions (wrench icon) > Prefs > Gesture controls > Quick Menu. Set a trigger, then open the menu, tap one of the slots, and choose Recolor from the list. Procreate has moved this tool between versions, so if you can't find it, check this menu first.
- Select the right layer. Recolor only affects the active layer, and this is where most mistakes happen.
- Trigger Recolor. A small crosshair appears on the canvas.
- Drag the crosshair onto the color you want to change. The crosshair position decides which color region gets replaced. If the whole background changes, the crosshair is sitting on the wrong area.
- Choose a new color. Recolor updates in real time, so you can scrub through the color wheel and watch the result.
- Adjust the flood threshold at the bottom of the screen if the fill leaves gaps or leaks into adjacent areas.
Recolor works best on a flat layer with a single dominant color. On layers with several colors or heavy texture, the result changes depending on where the crosshair sits, so expect to nudge it around until it behaves.
Method 2: ColorDrop
ColorDrop is the more direct route when you already know what color you want.
- Select the layer.
- Drag from the color dot in the top-right corner straight onto the shape you want to fill. Sweep immediately without pausing on the dot, or it can switch to your previously used color.
ColorDrop replaces one contiguous region at a time. If you have a repeated element, like a pattern of identical dots, you'll need to drop on each one. That's fine for a handful of shapes and tedious for dozens. For many shapes, use selection-based recoloring instead.
Method 3: Select by color, then fill
This is the most controlled method for a single color that appears in many places on the same layer.
- Open the Selection tool and switch the mode to Color.
- Tap the color you want to change. Procreate selects pixels that match, and you can drag to adjust the selection threshold.
- Choose a new color and fill the selection (drag the color dot in, or use Fill Layer from the layer menu).
Because the selection spans the whole layer, you catch every instance of that color at once. Check the edges up close afterward. Anti-aliased pixels that fall just outside your threshold may keep a ring of the old color. Raising the threshold or feathering the selection slightly usually fixes it.
Method 4: Alpha Lock
Alpha Lock is the right answer when you want to recolor everything painted on a layer, like turning black lettering white or pink.
- Swipe right with two fingers on the layer in the Layers panel. A checkerboard pattern on the thumbnail confirms Alpha Lock is on.
- Select your new color.
- Fill the layer, or paint over it with any brush. Only the pixels that already exist on the layer accept the new color, and transparent areas stay untouched.
Alpha Lock preserves the original edge softness, so it avoids the jagged outlines you can get from selection-based fills. Its limitation is that it's all-or-nothing per layer. If you only want to change one color among several on that layer, combine it with a selection first.
Method 5: Adjustments (Hue, Saturation, Brightness)
Adjustments shift color relationships rather than replacing a specific color.
- Hue, Saturation, Brightness: Open Adjustments (the magic wand icon) > Hue, Saturation, Brightness. Hue slides every color on the layer around the spectrum, Saturation controls intensity, and Brightness controls lightness. Tap the Adjustments icon again to commit, or use a two-finger tap to undo.
- Color Balance: Splits changes into Shadows, Midtones, and Highlights, with red/cyan, green/magenta, and blue/yellow sliders. Midtones are selected by default and give the most even adjustment.
- Curves: The most precise option for tweaking contrast and individual color channels together.
To make an adjustment affect only one color, make a selection first (Method 3), then apply the adjustment. Procreate limits the effect to the selected area. Otherwise, the adjustment applies to the entire layer, which is why isolating your element on its own layer matters so much.
Method 6: Clipping mask with a Color blend mode
If you want to preserve the original artwork and change your mind later, don't alter the pixels at all.
- Create a new layer directly above the artwork.
- Tap the new layer and choose Clipping Mask, so it only affects what's beneath it.
- Set the blend mode to Color. Try other blend modes if you want to keep more of the original shading.
- Paint over the area you want recolored.
Because the recolor lives on its own layer, you can delete it, change its opacity, or repaint it without damaging the original. This is the most production-friendly method, especially when art directors request color revisions.
Fixing common problems
- The whole canvas changed color. You were on the wrong layer, or Recolor's crosshair was sitting on a large background region. Undo, select the correct layer, and move the crosshair onto your target.
- Leftover halos around edges. Anti-aliased edge pixels sit between two colors and don't match either. Raise the threshold, use a slightly feathered selection, or switch to Alpha Lock or a Color blend layer.
- Banding or muddy results on textured art. Flood-fill methods struggle with grain. Use a Color blend clipping layer so the texture underneath stays intact.
- Gradients turn flat. Fill-based methods replace tonal variation. Use Hue or Color Balance instead, which preserve it.
Taking recolored Procreate art into a motion pipeline
If your Procreate work is heading into After Effects, Premiere Pro, or a Nuke comp, think about where the recolor should happen. Export your layers with transparency, or as a layered file, so you can adjust the color downstream if needed. In your compositing tool, color-adjustment effects can retarget a single hue without going back to the iPad. Doing the swap in Procreate pays off when the color change is baked into the art's design, and doing it in the comp pays off when the client may ask for another round.
This is also where Styleframe can fit in. It's an AI video and motion tool built for artistic control rather than one-click output. If you want to carry a Procreate frame's look into moving imagery, you can use the illustration as a reference.
Your compositing workflow stays the same, and Procreate remains the place where you define the palette.
Quick FAQ
Can I change one color without affecting the rest of the layer? Yes. Use Selection in Color mode to isolate the color, then fill it or apply an adjustment. Recolor and ColorDrop also work when the color region is contiguous and cleanly defined.
What's the best non-destructive method? A clipping mask set to the Color blend mode. The original pixels stay unchanged and you can revise the recolor at any time.
Why does Recolor behave unpredictably on textured art? It samples the color under the crosshair and floods based on a threshold. Texture introduces many near-matching colors, so small crosshair movements change the result. A Color blend layer or color-based selection is more reliable.
Does Hue adjustment change just one color? No. It shifts every color on the layer. Make a selection first, or isolate the element on its own layer, to limit the effect.