How to Center Layers in Procreate
StyleFrame Team7 min read
Procreate has no align panel, so you center a layer by selecting it, opening the Transform tool, turning on Snapping, and dragging until the yellow vertical and horizontal guides both appear at the middle of the canvas. For finer control, set a 2D Grid to its maximum size or use a Symmetry guide with Quadrant enabled, so the center axes are visible while you transform. Group multiple layers first so they move as one unit and keep their spacing.
The Fast Method: Transform with Snapping
This is the method to reach for first, and it works on a single layer or a group.
- Select the layer (or group) in the Layers panel.
- Tap the Transform arrow in the top toolbar. A bounding box appears around the layer's contents.
- In the bottom bar, tap Snapping to turn it on.
- Drag the layer slowly using a finger or the stylus, from inside the box.
- When a yellow vertical line appears at the canvas midpoint, the layer is horizontally centered. When a yellow horizontal line appears, it is vertically centered.
- Stop when both lines show and meet at the center node of the bounding box.
One detail trips people up: Procreate centers the bounding box of the layer's pixels, not the visual weight of your artwork. If a layer has a stray speck of paint far from the main subject, the box stretches to include it, and your subject will look off-center even though the snap says otherwise. Clean up stray marks or select just the artwork first (more on that below).
Tuning Snapping So It Actually Helps
If snapping feels either too grabby or not grabby enough, open the Snapping settings. Two sliders matter.
- Distance sets how close, in pixels, the layer needs to be to a guide before it jumps to it. A high value snaps from farther away; a low value forces you to get close.
- Velocity sets how fast you can drag and still have guides catch. At high values you need to move slowly for guides to engage, and a quick drag passes straight through them so you can place things freely.
For precise centering, a moderate distance and a higher velocity setting work well: you drag slowly near the middle, the guide grabs, and quick repositioning elsewhere isn't hijacked.
Show Center Lines with a 2D Grid
Snapping tells you when you hit center, but a persistent visual reference helps when you're checking a composition by eye. A trick that works well is turning the 2D Grid into a crosshair.
- Open the Actions menu (wrench icon) and go to Canvas.
- Turn on Drawing Guide, then tap Edit Drawing Guide.
- Choose 2D Grid.
- Drag the grid size slider all the way to the right. At maximum size, the grid collapses to little more than the center horizontal and center vertical lines.
- Tap Done.
Now Transform your layer and align the bounding box's center node with the crosshair. Combined with Snapping, this gives you both a visual check and a magnetic one. You can also nudge a selection one pixel at a time by tapping just outside the bounding box on the side you want it to move toward, which is handy for last-pixel corrections.
When you drag, grab outside the bounding box handles' influence. Starting a drag on a corner node scales or distorts the layer instead of moving it.
Use a Symmetry Guide with Quadrant
Another option is a Symmetry guide, which gives you true center axes without fiddling with grid size.
- Go to Actions > Canvas > Drawing Guide > Edit Drawing Guide.
- Choose Symmetry.
- Enable Quadrant at the bottom.
- Tap Done.
When you open Transform, you'll see a center point plus horizontal and vertical axes. Line the bounding box's center node up with the intersection. It isn't automatic centering, and some artists find it a bit like eyeballing, but paired with Snapping it gets you to a reliable result. It also doubles as a helpful construction guide if you plan to draw symmetrical elements afterward.
The Edge-Touching Workaround for Pixel-Accurate Centering
When you need the layer centered exactly and don't trust your eye, there's a community workaround using Transform's Fit to Screen command. It works because Fit to Screen scales the selection until it meets the canvas edges. If your content already touches those edges, the only thing left to change is its position.
- Put the content you want centered in a single layer or a group.
- Inside that group, add a new layer and draw a line that spans from the left edge of the canvas to the right edge, passing roughly through the middle of your artwork.
- Select the group, open Transform, and tap Fit to Screen. Because the content already touches the left and right edges, the width doesn't change and the group is centered vertically.
- Clear that line and instead draw a line from the top edge to the bottom edge.
- Select the group again, run Fit to Screen again, and it centers horizontally.
- Delete the helper layer.
Caveats: this fails if any mask, clipping mask, or other layer in the selection already extends to a canvas edge, because that changes the bounding box. It also takes more steps than snapping, so save it for cases where exactness matters. Check the result afterward, since Fit to Screen can alter scale depending on your content's proportions.
Resize Without Losing the Center
Centering is easy to undo accidentally. Dragging a corner handle pulls the layer off center. Instead:
- Set Transform to Uniform or Freeform.
- Use a two-finger pinch inside the bounding box. This engages Quick Scale, which scales around the midpoint of the selection, so the layer grows or shrinks symmetrically from the center.
- Watch for slight tilt, since two-finger gestures can introduce a small rotation. Checking the angle after scaling avoids surprises.
If you want a layer to fill the canvas and sit centered in one move, Fit to Screen does that by scaling the layer up to the canvas bounds while keeping it centered. Just remember it changes scale, so don't use it when you need to preserve the layer's size.
Centering Several Layers at Once
To center a composition rather than individual pieces, don't center each layer separately. You'll lose the relationships between elements.
- Group the layers and Transform the group. The layers move as one block with spacing intact.
- To center a subject on a layer that has background or stray content, use Select to isolate the subject, then Transform the selection. Centering is based on the selection's bounding box, which is more accurate than the whole layer.
Troubleshooting
- Snapping guides never appear. Confirm Snapping is toggled on and that Distance isn't set too low. Slow your drag if Velocity is high.
- The layer looks off-center despite the guides. Hidden or faint pixels are probably extending the bounding box. Select the visible artwork and transform that instead.
- Clipping masks distort the result. Clipped layers can extend to canvas edges. Merge or temporarily release them before centering.
- Accuracy matters at print or delivery scale. Zoom in and confirm alignment, then nudge by tapping outside the bounding box.
Handing Centered Art Off to After Effects
If your Procreate work feeds an animation or video pipeline, set the canvas to your comp's pixel dimensions before you start, so "centered on canvas" means "centered in frame." Once the layers are in your compositing software, you can use its alignment tools to check or adjust centering.
Summary
For most jobs, Transform with Snapping is all you need: select, drag slowly, and stop where both yellow lines meet. Add a maxed-out 2D Grid or a Quadrant Symmetry guide when you want a persistent visual reference, and use the Fit to Screen edge-line trick for pixel-exact results. Group layers to keep composition intact, scale with a two-finger pinch to hold the center, and match your canvas to your comp size so everything lines up when it reaches After Effects.