How to Center Art in Procreate
StyleFrame Team8 min read
Procreate has no alignment panel, so you center art with Transform. Select the layer, tap the Transform arrow, turn on Snapping, and drag until the yellow vertical and horizontal guides both appear at the canvas midpoint. For a permanent visual reference, set a 2D Grid drawing guide to its maximum size so only the center crosshair remains. If you need to center and scale at once, Transform's Fit to Canvas does both.
Why centering in Procreate takes a workaround
Photoshop has an alignment panel that centers a layer against the canvas. Procreate doesn't. Its own community forum has long-running feature requests for align and center commands, and the standard answer is to combine Transform, snapping, and drawing guides.
None of these methods is hard, but they differ in precision and speed. Which one you pick depends on whether you're nudging a single layer, centering a whole group, or setting up a canvas you'll hand off to a compositor.
Method 1: Center with Transform snapping
This is the fastest method for most artwork.
- Select the layer or group you want to center.
- Tap the Transform tool (the arrow icon in the top toolbar).
- In the bottom bar, turn on Snapping (called Magnetics in some versions and interface languages).
- Drag the artwork slowly.
- When a yellow vertical line appears down the middle of the canvas, the artwork is centered horizontally. When a yellow horizontal line appears across the middle, it's centered vertically.
Once both guides are visible and meet at the center node of the transform box, you're centered. Lift your finger or stylus only after both guides appear, because releasing early leaves you a few pixels off.
Tune Distance and Velocity
If snapping feels either too sticky or too absent, open the Snapping submenu. Two sliders control the behavior:
- Distance sets how close, in pixels, the artwork must be to a guide before it jumps to it. A high value catches from farther away. A low value demands you get very close.
- Velocity sets how slowly you must move for guides to engage. At a high setting, you have to drag slowly for snapping to catch. A fast drag passes through the guides so you can reposition freely.
For precise centering, use a moderate Distance and drag slowly. Raise Velocity sensitivity if you keep overshooting or sticking to guides you don't want.
Method 2: Show only the center lines with the 2D Grid
Snapping tells you when you hit center, but sometimes you want to see the center before you draw. A maxed-out 2D Grid gives you that.
- Open Actions (the wrench icon) → Canvas.
- Turn on Drawing Guide, then tap Edit Drawing Guide.
- Choose 2D Grid.
- Drag the grid size slider all the way to the right.
- Tap Done.
At maximum size, the grid collapses to a single horizontal and a single vertical line crossing at the canvas center. You get a clean crosshair to draw against, and it also works as a reference when you align Transform handles manually. Pair it with snapping and you have both a visual target and a magnetic catch.
This is a good setup for logos, title cards, symmetrical layouts, and anything where the center is a compositional anchor.
Method 3: Use the Symmetry guide's Quadrant option
If you want a center point and axes visible during Transform, the Symmetry guide is a useful alternative.
- Go to Actions → Canvas and turn on Drawing Guide.
- Tap Edit Drawing Guide and choose Symmetry.
- Enable Quadrant at the bottom, then tap Done.
- Tap Transform. You'll now see a center point and the horizontal and vertical axes.
- Line up the transform box's center node with those axes.
This isn't automatic snap-centering, and it's closer to guided eyeballing than true alignment. It's still helpful when you want a persistent center point, and it can be easier to read than a grid on a busy canvas. If you only need the guide for centering and not for drawing symmetrically, turn Symmetry drawing off afterward so you don't mirror strokes by accident.
Method 4: Fit to Canvas for centering and scaling at once
When the goal is to fill the canvas as well as center, use the one-tap option:
- Select the layer.
- Tap Transform.
- Tap Fit to Canvas (labeled Fit to Screen in some versions) in the bottom bar.
Procreate scales the content up or down to the canvas's maximum proportions and centers it. This works well for imported photos, textures, and reference plates. It's a poor choice for art that should keep its current scale, because it will resize.
Method 5: The edge-line trick for layer groups
Fit to Canvas can also be used to center something without changing its size, as long as you control what the transform box contains. This workaround comes from the Procreate community and is useful when snapping is fussy, such as with a group of many layers.
- Put everything you want to center into a layer group.
- Inside the group, add a new layer and draw a line that touches both the left and right edges of the canvas, passing roughly through your artwork vertically.
- Select the group, tap Transform, then Fit to Canvas. Because the content already spans the full width, only the vertical position changes, and the artwork centers vertically.
- Clear that helper layer, then draw a line that touches both the top and bottom edges, passing through your artwork.
- Select the group and use Fit to Canvas again. This time the horizontal position centers.
- Delete the helper layer.
It takes more steps than snapping, but it's repeatable and doesn't depend on how steady your hand is. The caveat is that any mask, clipping mask, or stray pixel that already reaches a canvas edge changes the bounds, and the result will be off. Check for those before you rely on this method.
Resize without losing the center
Centering a piece and then dragging a corner handle to resize will knock it off center. There are two clean ways to avoid that:
- Quick scale: In Uniform or Freeform transform mode, pinch with two fingers inside the bounding box. The scaling anchors on the midpoint of the selection, so the art grows or shrinks symmetrically from its center. Two-finger gestures can introduce a slight tilt, so check the rotation afterward.
- Re-snap after scaling: Resize however you like, then run Method 1 again to catch the center guides.
Why centering fails: common causes
When the result looks off, the cause is usually one of these:
- Stray marks. A single faint pixel far from your subject extends the layer's bounding box, so the "center" is the center of everything, not your subject. Zoom out and clean up.
- Masks and clipping masks. Content that reaches the edge of the canvas changes what Procreate treats as the artwork's extent. This is the main reason the edge-line trick fails.
- Canvas size changes. If you crop or resize the canvas after drawing, previously centered art shifts relative to the new center. Re-center after any canvas change.
- Multiple layers moved separately. Group them first, or merge copies, so they move as one unit.
- Optical vs. geometric center. Geometric centering of an irregular shape can look wrong. For logos and character art, shift slightly until it feels balanced.
Centering for a motion pipeline
If your Procreate art is headed into After Effects, Nuke, or a 3D tool, centering has downstream consequences beyond looking tidy.
- Match the canvas to the comp. Create the canvas at your delivery resolution and aspect ratio so you aren't scaling later. If you need to change it, resize the canvas, then re-center.
- Center before you export layers. A centered, consistent canvas makes anchor points predictable when you rotate or scale in your compositing software.
- Keep layers organized. Group elements that should move together, and name layers so the compositor doesn't have to guess.
- Avoid hidden edge content. Stray strokes touching the canvas edge change a layer's bounds when you import it, so clean up before export.
Quick reference
Final tips
Start by centering with Transform snapping, and tune Distance and Velocity until it feels predictable. Keep a max-size 2D Grid ready for layout-heavy work, and fall back on the edge-line trick when you need a repeatable result for a whole group. Clean up stray pixels and check your masks before you blame the method. For work headed to a compositor, set the canvas to your delivery size, center before you export, and keep layers tidy so the file works in After Effects or Nuke without cleanup.