How to Bucket Procreate
StyleFrame Team7 min read
In Procreate, the paint bucket is called ColorDrop. Drag the color swatch from the top-right corner onto a closed area of your canvas, keep holding, and slide left or right to set the fill threshold, then lift to commit. For fills on a separate layer, mark your line art layer as a Reference layer, select an empty layer beneath it, and drop the color there.
This guide covers every bucket-style method in Procreate, how to fix the usual problems (whole-layer floods, leaks, wrong-layer fills), and how flat-color artwork moves into a motion or compositing pipeline afterward.
The Fast Answer: ColorDrop Step by Step
ColorDrop behaves like a bucket, but the gesture is different from Photoshop or Clip Studio:
- Pick your color in the Colors icon at the top right.
- Press and drag from that color swatch into the shape you want to fill.
- Keep your Apple Pencil or finger down. After a moment, a blue Threshold indicator appears at the top of the canvas.
- Slide left to fill less, or right to fill more, and watch the percentage.
- Lift to commit the fill.
Procreate remembers your last threshold, so the next drop starts from the same value. If your fills suddenly behave differently, a threshold you adjusted earlier is usually the reason.
Adjusting Threshold for Clean Fills
Threshold decides how far the color spreads into pixels that are similar to the one you dropped on. A few rules of thumb:
- Too high: the color floods past your outline or covers the whole layer.
- Too low: you get a speckled fill with unfilled pixels near the edges.
- Soft or anti-aliased line art: push the threshold higher so the fill tucks under the semi-transparent edge pixels instead of leaving a pale halo.
Adjust while you are still holding. Once you lift, you have to undo and redo the drop with a new value.
Filling Multiple Areas With Continue Filling
Dragging from the top-right corner for every shape gets slow on a piece with dozens of regions. After a ColorDrop, tap Continue Filling at the top of the screen. Now each tap on the canvas fills that area with the same color. You can also tap, hold, and drag to change the threshold on the fly.
To exit, tap the tick at the top or switch to another tool such as Paint.
If you use an Apple Pencil on an iPad that supports hover, there is a shortcut. Hover the tip over your current color swatch and double-tap the side of the Pencil to enter Continue Filling with that color immediately.
Filling on a Separate Layer With a Reference Layer
The most common complaint from artists coming from other apps is that ColorDrop floods the whole layer. This happens because ColorDrop reads the pixels of the active layer. If you are on a blank layer, it sees nothing but empty pixels and fills everything.
The fix is a Reference layer, which lets you keep line art and flats separate:
- Open the Layers panel and tap the thumbnail of your line art layer.
- In the Layer Options menu, tap Reference.
- Create or select a new layer beneath the line art. This is where the color will go.
- Drop your color. ColorDrop reads the line art from the Reference layer but paints into your active layer.
This is the right setup for animation and compositing prep. Flats on their own layer stay editable, can be recolored independently, and export cleanly without baked-in outlines. If a fill still floods the whole layer after you set the Reference layer, check that the line art layer is actually the one marked Reference and that the active layer is a different one.
Other Bucket-Style Methods
ColorDrop is the main tool, but Procreate offers several alternatives that suit different jobs.
Recolor
Recolor is an older feature that was brought back. It lives in the QuickMenu, which is off by default. To enable it:
- Go to Actions → Prefs → Gesture Controls → QuickMenu.
- Choose how you want to trigger it.
- Assign one of the radial options to Recolor.
Then tap Recolor, pick your color, tap areas to fill, and use the Flood slider to control how aggressive the fill is. Some artists prefer it because it feels closer to a classic bucket.
Selections with Color Fill
If you want shapes filled the moment you select them:
- Tap Selections at the top.
- Choose a method from the bottom tabs: Automatic, Freehand, Rectangle, or Ellipse.
- Turn on Color Fill (it is active when highlighted blue).
- Pick your color and make the selection.
The area fills as soon as the selection completes. Color Fill stays on even if you exit and re-enter Selections, so turn it off when you are done, or your next selection will fill unexpectedly. It also only works on a single layer, not a group.
For soft-edged vignettes or framing, combine a Rectangle selection with Feather before filling.
Fill Layer
To flood an entire layer with one color, select the color, open Layers, tap the layer twice to open its options, and choose Fill Layer. This is useful for solid backgrounds, base mattes, or color-block layers you plan to mask or clip other artwork onto.
Troubleshooting Common Bucket Problems
The color floods the whole canvas or layer. Lower the threshold first. If that does nothing, you are probably filling a layer that has no line art on it. Set up a Reference layer as described above.
The fill leaks through a gap in the outline. ColorDrop has no dedicated gap-closing setting like some dedicated inking apps do. Close the gap with a small brush stroke on the line art layer, or lower the threshold so the fill stops before it escapes. For heavy inking and flatting work, some artists find other software faster; Procreate can do it, but it takes more patience.
A pale fringe remains around the edges. This is anti-aliasing. Raise the threshold slightly so the color extends under the soft pixels, or place the fill layer beneath the line art so the outline covers the seam.
You need to fill many separate areas with one color. Use Continue Filling or the Selections Color Fill method instead of re-dragging from the swatch each time.
You want a magic wand. Procreate's Automatic selection is the closest equivalent. Tap an area to select it, then use the selection tools to modify it. Artists who rely on expand, shrink, and invert selections on complex line art often keep a desktop app in their workflow for that step.
Getting Flat-Color Artwork Into a Motion Pipeline
For motion designers, animators, and compositors, a bucket fill is rarely the end of the job. Flat-color frames, character designs, and style frames usually need to become moving footage inside After Effects, Nuke, or a 3D tool. A few habits make the handoff smoother:
- Keep layers separated. Line art, flats, shading, and backgrounds on separate layers let you animate or composite them independently later.
- Name layers before export. A clear structure saves time when you import a layered file into After Effects.
- Export at the highest practical resolution. Check which layered and flat export formats Procreate offers and pick the one your pipeline accepts. Working large keeps your options open for reframing and push-ins.
- Check edges. Halos from anti-aliased fills become much more visible when footage is scaled or keyed.
Where Styleframe Fits
Once you have a clean illustrated frame, the next question is often how to extend it into motion without redrawing every frame by hand. is one option to explore for that step. Your compositing, color, and finishing can stay where they already live.
Quick Reference
Final Thoughts
Procreate's bucket is a gesture, not a tool you select, and the setting that matters most is the threshold. Learn that slider and the Reference layer workflow, and most "it filled everything" problems disappear. Keep your layers organized from the start, and your flat-color work will move cleanly into whatever animation, compositing, or AI-assisted motion step comes next.