How to Autofill in Procreate
StyleFrame Team7 min read
To autofill in Procreate, drag your active color from the top-right corner into a closed shape, which is called ColorDrop. Keep holding and slide left or right to set the Threshold, then lift to commit. If the fill floods the whole layer, lower the Threshold, or turn on Reference for your line art layer so the fill respects the lines while you paint on a separate layer.
The fastest method: ColorDrop and Continue Filling
ColorDrop is Procreate's paint bucket, and it is the right default for most flatting work.
- Set your color in the Colors icon at the top right.
- Drag that color dot onto the area you want to fill and keep your Apple Pencil or finger down.
- Pause, then slide left or right to adjust the Threshold. Left fills less and right fills more. The percentage shows at the top of the canvas.
- Lift to commit the fill.
Once you have dropped a color, tap Continue Filling to fill other areas with simple taps. You can also tap, hold, and drag to change the Threshold between fills. Exit by tapping the tick at the top or by switching to another tool such as Paint.
On an iPad and Apple Pencil that support hover, you can hover over your current color and double-tap the Pencil's side to jump straight into Continue Filling with that color.
Procreate remembers the Threshold you last used. If a fill suddenly behaves differently, check whether you changed it on the previous drop.
Why ColorDrop sometimes fills the whole layer
This is the most common complaint, and it usually has one of two causes:
- The Threshold is too high. A high value tells Procreate to treat a wide range of pixels as "similar," so the fill spreads past your lines. Drop the color again and pull the slider back toward the left.
- You're filling on a different layer than your line art. ColorDrop samples the layer you're on. On an empty layer, there are no lines to stop it, so it floods everything. The fix is a Reference layer, covered below.
Fill on a separate layer with Reference
Most illustrators keep line art on one layer and color on another so they can edit either without damaging the other. Procreate supports this with the Reference feature.
- Open the Layers panel.
- Tap the thumbnail of your line art layer to open Layer Options.
- Tap Reference.
- Select an empty layer underneath and use ColorDrop as usual.
Procreate now reads the boundaries from the reference layer and applies color to your active layer. For motion work, this is the setup to use, because you end up with clean separate layers that carry over into a compositing pipeline.
One limitation to plan for: users commonly note that Procreate lacks a dedicated gap-closing setting like the one in some inking-focused apps. If your lines have small openings, the fill can leak. Close the gaps with a quick brush stroke on the line layer, or lower the Threshold and accept some cleanup. Antialiased edges can also leave a faint halo between fill and line, so tuck your color layer under the line art instead of trying to match edges exactly.
Autofill with Selections and Color Fill
If you want a fill triggered by the act of selecting, use Selections → Color Fill.
- Tap Selections at the top.
- Pick a selection method from the bottom tabs: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it highlights blue.
- Choose your color in the top right.
- Make the selection. The area fills the moment the selection completes.
This works well for geometric shapes, backgrounds, and vignettes. Pairing a Rectangle selection with Feather can give you a soft-edged frame around a piece. Color Fill stays on after you leave Selections, so turn it off when you're finished or you'll fill areas by accident later.
Color Fill only works on a single layer, not on a group. If nothing happens, check that you've selected a layer and not a group.
Fill an entire layer
For a flat background or a base color, use Fill Layer:
- Choose your color.
- Open Layers and tap the target layer to open Layer Options.
- Tap Fill Layer.
This replaces the layer's contents with the color, so use it on a new, empty layer unless you mean to overwrite. If you want to recolor existing artwork while keeping its shape, turn on Alpha Lock for that layer first, then fill. Only the pixels that already exist will take the color.
Recolor, the older alternative
Recolor is an older method that Procreate removed and later brought back. It is only available through QuickMenu, which is off by default.
- Go to Actions → Prefs → Gesture Controls → QuickMenu and enable your preferred trigger.
- Assign Recolor to one of the radial slots.
- Invoke QuickMenu and tap Recolor.
- Pick a color and tap the areas to fill.
- Use the Flood slider to control how aggressively the fill spreads.
Recolor behaves much like ColorDrop with a Threshold. Choose it if you prefer tapping to dragging and don't mind the QuickMenu setup.
Which fill method to use
Troubleshooting common autofill problems
- The fill covers the whole canvas: lower the Threshold, or set up a Reference layer if you're filling on a separate layer.
- Gaps or leaks: close the openings in the line art, or fill on a layer beneath the lines.
- White or colored fringe at edges: put the color layer below the line layer, or fill slightly past the edge of the line.
- Color Fill isn't working: confirm you're on a single layer, not a group, and that Color Fill is highlighted blue.
- Fills behave inconsistently: the Threshold persists between uses, so check its value before the next drop.
Where Procreate fills fit in a motion pipeline
For motion designers, animators, and VFX artists, Procreate is often a concept stage: character designs, style frames, matte painting elements, and storyboards. Autofill earns its place there because clean flats on separate layers are easy to hand off.
A few habits make that handoff smoother:
- Keep line art, flats, shading, and background on separate named layers.
- Use Reference + ColorDrop so the color layers stay independent of the lines.
- Export layered PSD files for After Effects, Photoshop, or Nuke, or export flattened PNGs for reference.
- Fill characters on flat, solid colors so they are easy to isolate or key later.
Using those flats as references in Styleframe
Once you have a Procreate piece with clean flats, you can use it as the starting point for motion in . Styleframe is an AI video and motion tool built around artist control rather than one-click output. Every generation is driven by reference images, video clips, and keyframes that you supply.
Here is how that can work with an illustration made in Procreate:
- Frames-to-Video: use your illustrated frames as keyframes and let Styleframe generate the motion between them. You decide what the start and end states look like.
- Restyle and Ink-and-Paint: apply the look of a Procreate illustration, such as your line quality and color palette, to other footage or frames through reference-driven style transfer.
- 2D-to-3D and Turntable: take a flat character design toward a 3D form or a rotating view, useful for checking a design before building it in Cinema 4D or Blender.
- Remove Background and 4K Upscale: isolate a subject cleanly, and bring approved results up to production-ready 4K.
This is not a replacement for filling in Procreate. Procreate is where you make deliberate drawing decisions. Styleframe is for extending those decisions into motion while keeping your references in charge.
Quick workflow to remember
- Draw line art on its own layer and set it as Reference.
- Create a new layer underneath for color.
- ColorDrop into the closed shapes, adjusting the Threshold until fills stay inside the lines.
- Use Continue Filling for additional areas.
- Use Alpha Lock for later recoloring or shading.
- Export your layers for your compositing tool.
Once the Threshold and Reference setup is second nature, autofilling in Procreate becomes quick, and the layered files you end up with are far easier to move into the rest of your pipeline.