How to Adjust Transparency in Procreate
StyleFrame Team6 min read
In Procreate, open the Layers panel, tap the "N" beside the layer name, and drag the Opacity slider to set how transparent that layer is. For a faster route, tap the layer with two fingers and slide left to reduce opacity or right to increase it. Brush opacity is a separate control: the lower slider on the Sidebar. To fade only part of a layer, make a selection first, then use the two-finger layer gesture.
What "Opacity" Means in Procreate
Opacity in Procreate is how visible a pixel is. At 100%, it is fully solid. At 50%, it is half see-through. Procreate lets you control this at three levels, and mixing them up is a common source of confusion:
- Brush opacity: how transparent new strokes are as you paint.
- Layer opacity: how transparent an entire layer is, applied after the fact.
- Selection opacity: how transparent a selected area of a layer is.
The first two are adjustable at any time. The third is baked into the pixels the moment you commit it. If you come from After Effects, think of layer opacity as the Opacity property on a layer, and selection opacity as a destructive edit to the pixels themselves.
Method 1: Change Layer Opacity With the Layer Menu
This is the most reliable method, and it is non-destructive because you can return to it and change the value repeatedly.
- Tap the Layers icon (two overlapping squares) in the top right.
- Find the layer you want to change.
- Tap the small letter to the right of the layer name. It reads N by default, which stands for Normal blend mode.
- Drag the opacity slider that appears beneath the blend mode list.
The same panel holds the blend modes, so you can set opacity and blend mode together. That is useful when you are building shadows, glows, or texture overlays you plan to match against composite layers later.
Note that you can only adjust one layer at a time with this method.
Method 2: The Two-Finger Gesture
The faster route is a gesture:
- Open the Layers panel.
- Tap the target layer with two fingers at once (index and middle finger of the same hand works well).
- A slider appears at the top of the screen, starting at 100%.
- Slide left to make the layer more transparent, or right to make it more solid.
Lift your fingers to finish. This is handy when you are dialing in a value by eye, since you can watch the canvas change as you slide.
If the gesture undoes your last stroke instead of opening the slider, you are probably tapping the canvas rather than the layer in the panel. If two-finger tap to undo is turned on in your gesture settings, a two-finger tap on the canvas will undo. The two-finger tap has to land on the layer's row in the Layers panel.
Method 3: Change Opacity on a Selection
Sometimes you only want to fade part of a layer, such as a highlight, a limb overlapping a body, or a section of a background.
- Open the Selection tool and choose a method.
- Make your selection.
- Open the Layers panel.
- Tap the layer containing the paint with two fingers at the same time.
- Slide left on the canvas to reduce opacity, or right to increase it.
There is an important caveat. When you exit this mode, the change is applied to the pixels. You can undo it immediately, but you cannot come back later and re-tune it the way you can with a layer's opacity slider. Each application is final.
The practical workaround is to duplicate the layer before you change a selection, or to move the area you want to fade onto its own layer. That way you keep a non-destructive path and can tweak the value later, just like you would with a mask or a separate layer in After Effects.
One more detail: with an active selection, the opacity slider in the layer's N menu still changes the whole layer, not just the selection. Only the two-finger method respects the selection.
The Adjustments > Opacity Tool
Older versions of Procreate included an Opacity entry under Adjustments. You tapped Adjustments, then Opacity, and slid left or right on the canvas to change how transparent the active layer's contents were. A bar at the top showed the current value, starting at 100%. Buttons along the bottom let you cancel, undo, redo, or reset, and tapping the Adjustments icon again committed the change.
Some users have noticed the older opacity button behaves differently after updates. If you cannot find it in your version, use the layer N menu or the two-finger gesture instead. They cover the same ground, and the gesture also handles selections.
Brush Opacity and Why Strokes Look Too Faint
To control how transparent your strokes are as you paint:
- Select a brush.
- Drag the lower slider on the Sidebar up to increase brush opacity, or down to decrease it.
If your brush looks too transparent even with the slider at maximum, the likely culprit is Apple Pencil pressure. Many Procreate brushes tie opacity to pressure, so light strokes come out faint. Press harder, or check the brush's pressure settings.
Another thing worth checking is clipping masks. If the layer you are painting on is clipped to a layer beneath it, your paint will only show where the base layer has content. That can look like a transparency problem when it is actually masking.
Troubleshooting Common Opacity Problems
- Nothing seems to change: make sure the correct layer is active, and check whether you are adjusting a layer or a selection.
- The whole layer faded when you wanted a selection: use the two-finger gesture, not the N menu slider.
- The two-finger tap undoes strokes: tap the layer's row in the Layers panel, not the canvas.
- Strokes are too light: check the Sidebar slider and the brush's pressure settings.
- You cannot re-edit a selection fade: it was committed to the pixels. Undo right away, or work on a duplicate layer next time.
- Using Procreate Pocket on iPhone: the method differs slightly from the iPad version, so look for the layer options in the Pocket interface.
Opacity in a Motion Pipeline
For motion designers and animators, Procreate is often where concept frames, storyboards, textures, and hand-drawn elements get made before they move into After Effects, Premiere Pro, or Blender. A few habits make that handoff cleaner:
- Keep opacity on layers, not baked into pixels. Selection-based fades are permanent, so you lose the flexibility to adjust them later.
- Separate elements you expect to animate. If a glow or shadow will fade in motion, give it its own layer and set its opacity in your compositing app, where it can be keyframed.
Opacity values you set in Procreate are a starting point. For final timing and easing, a compositing app gives you keyframes and curves.
Quick Reference
Learn the difference between the three levels of opacity and most transparency issues in Procreate sort themselves out. Use layer opacity when you want flexibility, selection opacity when you accept a permanent change, and save the final fades and timing for your compositing app.