How to Adjust Streamline on Procreate
StyleFrame Team6 min read
In Procreate, open the Brush Library, tap the brush you want to edit, and tap it again to open Brush Studio. Go to the Stabilization tab, find StreamLine, and drag the Amount slider up for smoother, steadier lines or down toward zero for looser, more natural strokes. The Pressure slider just below it controls how gradually pressure builds along the stroke. Changes apply only to that brush, so duplicate it first if you want to keep the original.
How to adjust StreamLine step by step
- Tap the Brush icon to open the Brush Library.
- Swipe left on the brush and choose Duplicate. This gives you a safe copy to edit.
- Tap the duplicate to open Brush Studio.
- Select the Stabilization tab from the left-hand list.
- Under StreamLine, drag Amount to set how much wobble is smoothed out.
- Drag Pressure to set how quickly pressure response kicks in along the stroke.
- Scribble in the Drawing Pad preview to test the result.
The preview pad is the fastest way to tune a brush. Draw the kinds of strokes you actually need (long contours, short ticks, tight curves) before you commit to a value.
What the StreamLine controls actually do
StreamLine smooths wobbles and shakes in a line. It matters most for inking and calligraphy, where small tremors show up at full size. It has two controls.
- Amount: Higher values give a smoother, more even result. Lower values, or off, give more natural linework with visible hand variation.
- Pressure: Higher values stretch out the application of pressure, so a stroke ramps up more slowly and smoothly. Lower values, or off, make pressure take effect sooner as you press down.
StreamLine vs. Stabilization
Both live in the same tab, but they behave differently. Stabilization takes a moving average of your stroke and draws that average on the canvas, so higher values straighten and steady the line more aggressively. StreamLine focuses on removing wobbles and shakes in the line as you draw. Many artists use a moderate amount of each, and you can tune them independently inside Brush Studio.
Suggested StreamLine values by task
There is no universal correct number. Published guidance from Procreate artists varies a lot because it depends on the brush, your hand speed, and your style. These are reasonable starting points, not rules.
If lines feel like they trail behind your pencil, lower the Amount before changing anything else. If they still look shaky, raise it in increments of 10 and retest in the Drawing Pad.
Adjusting StreamLine in Procreate Pocket
The path is slightly different on iPhone. Open your project, select a brush, and tap the brush icon in the top menu to reach the brush settings. In the Stroke tab you'll find the StreamLine slider. Slide it right to increase smoothing. Start around 30–40% and adjust from there.
Global smoothing vs. per-brush smoothing
StreamLine in Brush Studio is per brush. Procreate also has a global option that affects every brush. Go to Actions (wrench) > Prefs > Pressure & Smoothing and adjust the Stabilization slider (0–100%).
Use global smoothing carefully:
- It overrides the feel of brushes that weren't designed for it, so every line is smoothed whether you want it or not.
- If your Apple Pencil suddenly feels laggy or less responsive, global stabilization is a common cause. Check it before blaming the brush.
- A low setting (roughly 10–15%) is a sensible starting point if you want a little help across the board. Turn it back down when you switch to loose sketching.
Per-brush settings are usually better. You can keep a heavily smoothed inking brush, a loose sketch pencil, and a mid-range storyboard brush, each with its own StreamLine values, without touching global preferences.
Troubleshooting StreamLine problems
Lines still look corrected at 0%
Users have reported residual smoothing even with StreamLine at zero. According to Procreate's team response on its forum, no StreamLine is applied when the slider is set to None, and what you're seeing is likely Apple Pencil's predictive stroke behavior. If it bothers you, check global stabilization first, then compare against a different brush to see whether the behavior is tied to one brush's settings.
The brush feels wrong after many edits
Open the brush in Brush Studio, go to About this Brush at the bottom of the left-hand list, and tap Reset Brush. This restores every setting, including stabilization, to the original. It's also why duplicating before editing is worth the extra swipe.
Stroke ends look cut off or curved
Users have reported tails, curved lines, or vanishing stroke ends, and the problem tends to get worse as StreamLine increases. If you see it, lower the Amount, test on another brush, and make sure the app and iPadOS are up to date. Persistent issues are worth reporting to Procreate support with a screen recording.
Tapering feels off
Taper is a separate tab in Brush Studio. If line starts and ends look blunt or mushy, adjust the Pressure Taper points there rather than raising StreamLine. Smoothing and tapering interact, so tune them together, but change one at a time.
Why line consistency matters in a motion pipeline
If you're an animator or motion designer, you probably use Procreate for the parts of the job that benefit from a pencil: styleframes, storyboards, character and prop design, roto passes, hand-drawn textures, and overlays. StreamLine settings affect those assets in practical ways.
- Consistency across frames or assets. If you draw a set of elements, such as a family of icons or a sequence of boards, use the same duplicated brush with locked-in values. Changing StreamLine midway shows up as inconsistent line quality when assets are composited together.
- Intentional wobble. Hand-drawn "boil" and loose line work often read as more alive with StreamLine low. If the final look is a clean vector-like line, go higher.
- Export-ready art. Work at a canvas size that holds up in your composition, keep line art on its own layers, and export a PNG with a transparent background so you can bring it into your compositing tool without flattening your options.
Using Procreate artwork in Styleframe
Once you have a drawing with the line quality you want, you can carry it into an AI-assisted motion workflow without giving up control. Styleframe is an AI video and motion tool. Your Procreate art can serve as a reference input.
Styleframe doesn't change how you adjust StreamLine. It just means the line quality you set up in Procreate carries through as a reference rather than being averaged away.
Quick answers
Where is StreamLine in Procreate? In Brush Studio, under the Stabilization tab. In Procreate Pocket, it's in the Stroke tab of the brush settings.
What's a good StreamLine setting? For inking, many artists use 70–100%. For sketching, much lower values work better. On Pocket, 30–40% is a commonly suggested starting point.
Does StreamLine affect all brushes? No. It's per brush. For a global effect, use Actions > Prefs > Pressure & Smoothing.
Can I undo my brush changes? Yes. Use Reset Brush under About this Brush, or keep a duplicate of the original before you start editing.