How to Adjust Stabilizer in Procreate
StyleFrame Team7 min read
To adjust stabilization in Procreate, tap the wrench (Actions) icon, choose Prefs, open Pressure and Smoothing, and raise the Stabilization and Motion Filtering sliders until your lines come out as smooth as you want. Those global values apply to every brush. To tune one brush instead, open it in Brush Studio and change its Stabilization settings: StreamLine, Stabilization, and Motion Filtering.
Adjust Global Stabilization in Procreate
Global stabilization is the fastest way to clean up wobbly lines across a whole project. It is a good fit for animatics, storyboards, rotoscope-style tracing, and vector-like linework that will later be cleaned up or composited.
- Open a canvas and tap the wrench icon to open the Actions menu.
- Choose Prefs.
- Scroll about halfway down and tap Pressure and Smoothing.
- Raise the Stabilization and Motion Filtering sliders.
- Draw a few test strokes, then go back and adjust.
One caveat: these settings are universal. Whatever you set here affects every brush, not just the one you are using, until you change the values back. If you switch between a textured sketching brush and a clean inking brush, a high global value can make the sketching brush feel sluggish. Remember to reset it, or use per-brush settings instead (covered below).
A common starting point is a moderate value, around 50 for both sliders. Treat that as a starting point, not a rule. The right amount depends on your drawing speed, canvas zoom level, and how clean the final line needs to be.
What Stabilization and Motion Filtering Actually Do
Procreate builds a stroke by plotting many points along the path your Apple Pencil or finger travels. Stabilization and motion filtering are two separate smoothing controls that work on that path.
- Stabilization takes a moving average of your stroke and draws that on the canvas. The higher the value, the more it averages out wobbles. The tradeoff is that the line trails slightly behind your pencil, which feels like drawing with a bit of drag.
- Motion Filtering is the second smoothing slider in the same menu. Adjust it alongside Stabilization and test how each one changes your line.
Used together, they produce smooth, confident curves, the kind you want for a lagoon shape, a lettering curve, or a long contour line. Used at maximum, they can flatten the character out of a line and round off sharp corners. Raise them gradually.
Adjust Stabilization Per Brush in Brush Studio
Procreate lets you apply stabilization globally or to individual brushes. Per-brush control is usually the better choice for production work, because inking, sketching, and lettering brushes need different amounts of smoothing.
To get to it:
- Open the Brush Library and tap the brush you want to edit. Brush Studio opens.
- Select the Stabilization attribute from the list.
- Adjust the sliders and test the result in the drawing pad on the same screen.
- Save the changes to that brush.
Consider duplicating the brush before editing so you keep the original.
StreamLine
StreamLine smooths out wobbles and shakes in your line, and it matters most for inking and calligraphy. It has two controls:
- Amount: Turn it up for a smooth, even result. Turn it down or off for more natural, less polished linework.
- Pressure: Turn it up for a longer, smoother application of pressure along the stroke. Turn it down or off so pressure kicks in faster as you press.
If your lines look good but the thickness changes feel abrupt, the Pressure slider is the one to adjust, not Amount.
Stabilization and Motion Filtering at brush level
The same moving-average logic applies per brush. The benefit is that you can build a small kit: a heavily stabilized brush for clean outlines, a lightly stabilized brush for gesture and rough animation passes, and nearly raw input for texture and shading brushes.
Suggested Starting Values by Task
These are rough starting points to adapt, not official settings. Everyone's hand speed and zoom level differ.
Tip: stabilization may feel different at different zoom levels, so the same slider value can feel stronger or weaker. Test at the zoom level you will actually work at.
When Stabilization Doesn't Behave
Lines lag behind the pencil. You have set Stabilization too high. Lower it a bit and try Motion Filtering or StreamLine instead.
Corners come out rounded. High smoothing averages the path, which softens sharp turns. Lower the value for hard-edged work, or lift the pencil and draw each straight segment as its own stroke.
Changes to one brush affected everything. You changed the global Pressure and Smoothing values instead of the brush-level ones. Reset the global sliders and set the values inside Brush Studio.
A curved shape snaps into a polygon. Quick Shape (holding your pencil at the end of a stroke) can snap a stroke into a polyline, and it has no setting for freeform curves. For organic curves, stabilization is the better tool than Quick Shape.
Strokes still look jittery. Check the brush itself. Jitter and Spacing settings in Brush Studio can add variation to stamp placement independent of stabilization. Reducing Spacing Jitter or Jitter Lateral and Linear may be what you need, not more smoothing.
You can't tell which setting is responsible. Change one slider at a time and draw the same test stroke, such as a long S-curve, each time.
A Practical Workflow for Animators and Motion Designers
If you use Procreate alongside After Effects, Premiere Pro, or Nuke, stabilization settings are a small part of a bigger pipeline question: how consistent do your drawn assets need to be?
- Keep settings consistent across a sequence. If you are drawing frames, boards, or overlays that will be composited together, changing stabilization partway through will change the character of the line. Save a dedicated brush with your chosen values rather than relying on global settings you might forget to reset.
- Draw at the final resolution. Smoothing is applied to your input path. If you scale artwork up significantly later, you may expose the stroke's character. Set your canvas size for the delivery you need.
- Export for compositing. Export your artwork from Procreate in a format your compositing app accepts. Export formats vary by version, so check your own build.
- Separate roughs from final lines. Use low stabilization on a rough layer for energy, then draw cleaner passes on a new layer with higher settings.
Quick Reference
- Global: Wrench icon → Prefs → Pressure and Smoothing → adjust Stabilization and Motion Filtering. Applies to all brushes.
- Per brush: Brush Library → tap brush → Brush Studio → Stabilization → adjust StreamLine, Stabilization, Motion Filtering.
- Too laggy: Lower Stabilization, try Motion Filtering or StreamLine.
- Too jittery: Raise Motion Filtering or StreamLine Amount, and check the brush's jitter settings.
- Best practice: Save dedicated brushes for each job instead of re-tuning global settings every time.
FAQ
Is stabilization the same as StreamLine? No. Both smooth strokes, but StreamLine specifically assists with wobbles and shakes and is especially useful for inking and calligraphy. Stabilization averages the stroke path, and it can add a sense of lag at high values.
Can I turn stabilization off for one brush? Yes. Set the values low or off in that brush's Stabilization settings inside Brush Studio. Just make sure your global values are not overriding what you expect.
Why do my lines still look rough after raising the sliders? The cause may be brush attributes such as jitter or spacing, pencil pressure behavior, or a canvas that is too small for the zoom level you draw at.
Should I use high stabilization for animation frames? For clean final linework, often yes. For rough passes, lower values preserve the energy of the drawing. Many artists keep two brushes and switch between them.