How to Adjust Smoothing in Procreate
StyleFrame Team7 min read
To adjust smoothing in Procreate, tap the Actions (wrench) icon, go to Prefs > Pressure and Smoothing, and drag the Stabilization slider (0-100%) to set smoothing for every brush. For per-brush control, open the brush in Brush Studio and use the Stabilization tab, where StreamLine and Stabilization amounts affect only that brush. Start low, around 10-15%, and raise it until wobble disappears without making the pencil feel laggy.
Where Procreate's Smoothing Controls Live
Procreate splits smoothing across two places, and mixing them up causes most "my brush feels weird" problems.
- Global: Actions > Prefs > Pressure and Smoothing. These settings apply to every brush on top of whatever each brush already does.
- Per brush: Brush Library > tap a brush to open Brush Studio > Stabilization tab. These settings travel with the brush and affect only that brush.
Global is a blunt instrument, good for a session where you need everything clean. Per-brush is better for a permanent inking brush. Check both before you assume a brush is broken.
How to Adjust Global Smoothing Step by Step
- Tap the Actions (wrench) icon.
- Tap Prefs, then Pressure and Smoothing.
- Drag the Stabilization slider to set how aggressively strokes are smoothed and straightened.
- Adjust Motion Filtering to help smooth out small, unintentional motion in your hand movement.
- Experiment with Motion Filtering Expression to see how it changes the feel as you draw.
- Draw a few test curves and loops on a scratch layer, then fine-tune.
One video tutorial shows how personal this is. It pushes both Stabilization and Motion Filtering to roughly 50 to draw a clean, curving shape in a single stroke, while advising viewers to find values that feel right to them rather than copying the numbers. Treat any figure as a starting point, not a recipe.
What Each Slider Does
Stabilization smooths and straightens your stroke. In practice, the line trails slightly behind your pencil tip, like pulling it on a short rope. Higher values yield longer, more confident curves but add visible lag.
Motion Filtering helps smooth out small, unintentional motion in your hand movement. It's worth trying if your hand shakes on tight arcs or at the start of a stroke.
Expression is a further control for Motion Filtering. Test it with fast and slow strokes rather than reading it off the slider.
Recommended Starting Values
Begin around 10-15% Stabilization and work upward. Many artists find that moderate settings give polish without making the pencil feel disconnected. A reasonable approach:
- Sketching and gesture work: 0-10%. Keep energy and speed.
- Clean linework and storyboard outlines: 15-35%. Enough to kill wobble on long curves.
- Long single-stroke shapes, lettering, or smooth vector-like contours: higher values, tested stroke by stroke.
Remember to turn it back down when you switch tasks. A forgotten global stabilization setting is one of the most common causes of a pencil that feels sluggish or unresponsive, and it's easy to blame the hardware instead.
Adjusting Smoothing on a Single Brush
For a brush you'll reuse, adjust it in Brush Studio instead of globally.
- Open the Brush Library and swipe left on the brush to duplicate it. Always edit the copy.
- Tap the duplicate to open Brush Studio.
- Choose the Stabilization tab from the left-hand list.
- Raise StreamLine > Amount to reduce wobbles and shakes in the stroke.
- Raise Stabilization > Amount to smooth and straighten the stroke further.
- Test on a blank canvas.
StreamLine and Stabilization behave differently. StreamLine reduces wobbles and shakes as you draw, which is helpful for inking and handwriting-style curves. Stabilization smooths and straightens the stroke. Many inking brushes work best with a bit of both rather than a lot of either.
Resetting a Brush
If you've tweaked several values and lost track, open the brush, go to About this Brush at the bottom of the left-hand list, and tap Reset Brush. It restores every setting, including stabilization, to the original.
Smoothing vs. Pressure Curve
People often confuse smoothing with pressure response, but they solve different problems. The Pressure and Smoothing screen also contains a pressure graph: pencil pressure runs along the X axis, and the effect on the brush runs up the Y axis. If a brush takes too much force to become opaque or thick, tap the curve to add a node and lift it slightly, so the same pressure produces a stronger result.
Procreate cautions against changing the global pressure curve unless you need to, because brushes are tuned to work for most people and a custom curve can produce unexpected results. If you do get lost, scroll to the bottom of the Pressure and Smoothing screen and tap Reset all, then confirm.
If your lines look shaky because the thickness jumps around, the curve is probably the issue. If the path itself is wobbly, use stabilization.
When You Should Turn Smoothing Down
More smoothing isn't always better. Reduce or switch it off when you need:
- Energy and gesture: loose animation thumbnails, rough character poses, and expressive sketches.
- Texture: frayed edges, fur, grit, dry-brush marks, or hand-lettered imperfection.
- Sharp corners: hard-surface shapes, panel borders, and technical details where precision beats flow.
- Fast timing notes: quick annotations over frames where lag would slow you down.
Heavy smoothing also tends to round off corners, which can make a design look soft or generic. Match the setting to the job and change it between layers if you need to.
Troubleshooting Smoothing Problems
The pencil feels laggy or late. Check global Stabilization first, then the brush's own Stabilization and StreamLine values.
Lines are still wobbly after raising smoothing. Try drawing with your whole arm instead of your wrist, rotate the canvas so the curve matches your hand's natural arc, and use a few warm-up ovals and arcs before you ink. Software helps, but it doesn't replace a comfortable stroke direction.
A brush behaves differently from what you expect. The brush may have been edited. Reset it from About this Brush, or restore global values with Reset all.
Curves look polygonal. If you need a perfect shape, QuickShape (hold your pencil at the end of a stroke) snaps lines into clean primitives. It only works on shapes it recognizes, though, so freehand organic curves still need stabilization.
Where Smoothing Fits in a Motion Design Pipeline
Many motion designers, animators, and compositors use Procreate for storyboards, style frames, character designs, matte paintings, hand-drawn textures, and frame-by-frame passes. Clean, consistent linework matters here because anything you draw will be scaled, tracked, or composited later in After Effects, Nuke, or Blender. A wobbly stroke that looks fine on a tablet becomes obvious on a 4K timeline.
Some practical habits:
- Match smoothing across a set. For a sequence of frames or a family of boards, lock your stabilization values so the line quality stays consistent.
- Draw on separate layers for line, color, and shadow so you can export and recombine them in your compositor.
- Work at high resolution. Smoothing helps the path, but resolution determines how the edge holds up when you scale.
- Export flattened PNGs or layered files for import into After Effects, Premiere Pro, or Nuke.
Using Clean Procreate Art as a Reference in Styleframe
Smoothed, well-controlled drawings make strong inputs for AI-assisted motion work, because the tool follows what you give it. is one tool where clean hand-drawn references can serve as inputs.
Your Procreate drawings stay the creative source, and your compositor stays the finishing environment.
Quick Reference
Final Advice
Start with stabilization near 10-15%, adjust one slider at a time, and test on a scratch layer before committing to final art. Keep global settings low and put heavier smoothing on duplicated inking brushes so your defaults stay predictable. Once your lines are clean and consistent, you can carry them into After Effects, Nuke, or Styleframe with confidence that the drawing, not the software, defines the look.