How to Adjust Pressure Sensitivity in Procreate
StyleFrame Team7 min read
To adjust pressure sensitivity in Procreate, open Actions (wrench icon) > Prefs > Pressure and Smoothing, then drag the pressure curve graph. Raising the curve makes brushes respond to a lighter touch, and flattening it or dragging the top point to the left effectively turns pressure off. This is a global setting that affects every brush, and "Reset all" at the bottom of the menu restores the defaults. If only one brush feels wrong, adjust that brush in Brush Studio instead.
Where the pressure settings live
Procreate has two layers of pressure control, and mixing them up is the most common source of confusion.
- Global pressure curve: Actions > Prefs > Pressure and Smoothing. It applies to your stylus input across every brush.
- Per-brush dynamics: Brush Studio, where you adjust an individual brush's settings. These settings shape how a single brush reacts to pressure, including size, opacity, and softness.
Procreate only reads pressure from a connected, supported stylus such as an Apple Pencil. A generic stylus won't send pressure data. Procreate Pocket on iPhone also has no pressure sensitivity, so you adjust size and opacity manually there.
You must have a canvas open to reach the Prefs menu. Which canvas doesn't matter, because the changes are global.
How to adjust the pressure curve, step by step
- Open or create any canvas.
- Tap the Actions icon (wrench) in the top left.
- Choose Prefs, then Pressure and Smoothing.
- Find the pressure graph. The horizontal axis is how hard you press, from no pressure on the left to heavy pressure on the right. The vertical axis is how strongly Procreate applies that pressure to the brush, from no effect at the bottom to maximum effect at the top.
- Tap the line to add a node, then drag it to reshape the curve.
- Draw a few test strokes on the canvas, then return to the menu and refine.
Reading the curve
The default is a straight diagonal line, so the response scales evenly with pressure. Reshaping it changes how the pencil feels:
- Raise the middle of the curve if your strokes take too much force to build opacity or size. At the same pressure, the curve now sits higher on the vertical axis, so the brush shows up more with less effort. This suits a light hand, long drawing sessions, and quick sketching.
- Lower the middle of the curve if lines go dark or thick too fast. You'll need to press harder for the full effect, which gives finer control over subtle tonal shifts and thin-to-thick line transitions.
- Create an S-shape if you want a soft start, a responsive middle, and a quick ceiling. This works well for inking, where you want predictable thick and thin lines without having to bear down.
Make small moves. A small nudge to one node changes the feel more than you'd expect, and Procreate's own guidance is not to touch the global curve unless you need to, because its stock brushes are tuned for the default response.
How to turn pressure sensitivity off
Sometimes you want uniform lines, for example for technical linework, hard-edged shapes, or consistent outlines you'll later trace or convert to vector in another app.
- Go to Actions > Prefs > Pressure and Smoothing.
- Drag the top-right point of the pressure graph all the way to the top left. Get as close as you can if it won't go all the way.
- Draw a test stroke. Line thickness should now depend on the brush size slider rather than how hard you press.
To bring pressure back, tap Reset all at the bottom of the menu, or drag the point back to the top right so the line is a diagonal again. Note that Reset all also resets the other settings in that menu, including smoothing.
Adjusting smoothing and stabilization
The same menu has sliders at the top that control stabilization for all brushes. Increasing their values increases the amount of stabilization applied to all your brushes.
A practical approach for animators doing frame-by-frame work is to keep global smoothing modest and raise stabilization on specific inking brushes. That keeps your sketching brushes responsive while still giving you clean final lines.
Fine-tuning a single brush in Brush Studio
If only one brush feels off, don't touch the global curve. Open the brush in Brush Studio and look at its pressure-related settings. A few things to check:
- Size and opacity response: Brushes can be set to react to pressure in size, opacity, or both. If a brush won't thin out on a lighter touch, its pressure response may be too restrictive.
- Softness and size taper: Community advice for lines that won't respond as expected is to disable softness or taper effects on that brush and test again.
- Duplicate before editing: Duplicate a brush before changing it so you always have the original to fall back on.
This also explains a complaint that comes up often: a stroke that gets thicker as you press harder but won't thin again when you ease off. It usually comes from the curve or the brush's dynamics rather than a hardware fault. Move the lower point of the curve to the right a little at a time, or compare against a duplicate brush with taper turned off.
When pressure isn't working at all
If the pencil gives no pressure response, or only responds when you push very hard, work through these in order:
- Restart the iPad and re-pair the Apple Pencil by attaching it to the iPad.
- Test with a basic brush. Create a new canvas, pick a dark color, and use a simple painting brush with the sidebar sliders pushed to the top. Check that both the pencil and your finger draw.
- Reset gesture controls: Actions > Prefs > Gesture Controls > General > Reset to Defaults.
- Reset the pressure curve: Go to Actions > Prefs > Pressure and Smoothing and tap Reset all.
- Test a different Apple Pencil if you can borrow one. Procreate uses the pencil's pressure and tilt sensors more fully than many apps, so a hardware fault can show up in Procreate even if the pencil seems fine elsewhere.
- Confirm stylus support. Only a connected stylus that Procreate supports will send pressure data.
If another Pencil works and yours doesn't, contact Apple, especially if it's under warranty.
Presets worth trying
Because everyone's hand is different, these starting points are more useful than fixed numbers:
Test each change with the same set of strokes: a slow line, a fast flick, and a gradual light-to-heavy-to-light stroke. Repeating the same test makes it obvious whether a change improved your control.
Why this matters for motion and VFX work
For motion designers, Procreate is often where hand-made material gets created before it moves into a compositing pipeline: storyboards, style frames, texture passes, hand-drawn overlays, and frame-by-frame sequences. Inconsistent pressure response shows up quickly in motion. Line weight that varies unpredictably between frames creates visible flicker once the drawings are played back in sequence.
A few habits help:
- Lock your curve before starting a sequence. Don't change global pressure mid-project, or early and late frames will look different.
- Use one dedicated brush for line work across the whole sequence, and duplicate it for any variants.
- Turn pressure off for uniform outlines you plan to treat later, and let line variation come from the brush size you choose.
- Export at high resolution and bring layers into your compositing software, where you can control timing, blending, and compositing.
Quick recap
- Path: Actions > Prefs > Pressure and Smoothing.
- Raise the curve for a lighter touch, lower it for more resistance, flatten it to disable pressure.
- Use Reset all to return to defaults.
- For single-brush problems, edit a duplicate in Brush Studio rather than the global curve.
- If pressure fails entirely, restart, re-pair, reset, and test another Pencil.
- Lock your settings before starting a frame-by-frame sequence so line weight stays consistent.