How to Adjust Pressure Curve Procreate
StyleFrame Team7 min read
In Procreate, tap Actions (the wrench icon), go to Prefs, and open Pressure and Smoothing (some versions call it Edit Pressure Curve). Drag the graph's line, or tap it to add nodes, to change how Apple Pencil pressure (X axis) maps to brush effect (Y axis). Raising the curve at the low-pressure end makes light touches produce darker, thicker marks, and lowering it demands a firmer press. Tap Reset all at the bottom of the menu to return to the default straight diagonal.
What the Pressure Curve Actually Controls
The graph in Procreate's pressure settings is a response curve, and it works much like the Curves adjustment in Photoshop.
- X axis (input): how hard you press the Pencil, from no pressure on the far left to maximum pressure on the far right.
- Y axis (output): how strongly that pressure affects your brushes, from no effect at the bottom to maximum effect at the top.
By default, the line is a straight diagonal: each increment of pressure produces a proportional increase in effect. Any point you move above that diagonal means the brush responds more than expected for that amount of pressure. Any point below it means the brush responds less.
The curve is global. It applies to every brush, on top of whatever pressure behavior each brush already has in its own settings. That matters when you troubleshoot: if one brush feels off, the cause may be the brush, not the curve.
Step-by-Step: How to Adjust the Pressure Curve
- Open a canvas in Procreate and tap Actions (the wrench icon in the top left).
- Tap Prefs.
- Choose Pressure and Smoothing. In some versions, you'll see Edit Pressure Curve instead.
- Drag the line to reshape it. To add a node, tap anywhere on the line, then drag it up or down.
- To remove a node, tap it and choose Delete.
- Close the panel and draw a test stroke. Start light, press hard, then ease off.
- Go back and refine until the stroke feels natural.
Test with the brush you actually use for production work. A soft airbrush and a hard inking brush will reveal different problems, so it helps to scribble a few passes of each before you commit to a curve.
Common Curve Shapes and When to Use Them
Make light touches count (steeper start)
If you have to press hard to get a decent line, make the curve rise more steeply at the beginning. You can do this by dragging the top-right node left, or by adding a node near the center of the graph and lifting it slightly. Light pressure then reaches a higher effect sooner.
This compresses the faint-to-bold range of the brush into a narrower band of pressure, so you can reach a full-strength stroke without leaning on the screen. It's a common fix for sketching, where you want mid-gray tones to build up quickly instead of needing repeated passes. Light marks are still possible with a very feathery touch; you've just reduced the effort needed for the middle of the range.
Demand more pressure (flatter start)
Pull the curve down at the low end and the opposite happens. Light contact produces little or nothing, and you only get a bold line when you press firmly. This suits artists who find their hand too heavy-handed, or anyone who wants tight control over thin, delicate lines such as fine hatching or small lettering. Push it too far, though, and you'll have to press uncomfortably hard to get any visible mark.
The S-curve for smoother transitions
Adding a few nodes to create an S shape gives you a gentle response at light pressure and a more dramatic one as you press harder. Strokes start thin with a gradual transition, then thicken more quickly. This is useful for calligraphy, brush lettering, and any line work where varied width within a single stroke is the point.
Keep it modest
Procreate's own documentation recommends against changing global pressure settings unless you need to. The default brushes are designed to work for most cases, and an extreme curve can produce unexpected results across your whole brush library. Make small adjustments, test, and only go further if the problem persists.
Pressure vs. Smoothing: Don't Confuse the Two
The same menu includes sliders for stabilization (smoothing). Raising them increases the amount of stabilization applied to all your brushes, which steadies shaky lines but can introduce lag or soften deliberate gestures. Pressure and smoothing solve different problems:
- If strokes are the wrong weight or opacity, adjust the pressure curve.
- If strokes are the wrong shape (wobbly, jittery), adjust smoothing.
Changing both at the same time makes it hard to know which setting is helping, so adjust one, test, then move on to the other.
Troubleshooting Pressure Problems
Before you rework the curve, rule out simpler causes:
- Connection: Confirm Bluetooth is on and your Pencil shows as connected with a battery level. If you're using a different stylus, check that it supports pressure sensitivity.
- Individual brush settings: Open the brush's settings and check its Apple Pencil pressure properties. A brush configured to ignore pressure will not respond no matter what the global curve does.
- Accidental extreme curves: If things suddenly feel wrong after experimenting, reset the curve.
- Different needs per project: Many artists prefer a different curve for sketching than for inking or lettering. Procreate has one global curve, so note your preferred settings somewhere and re-enter them when you change task types.
How to Reset the Curve
If a tweak made things worse:
- Go to Actions → Prefs → Pressure and Smoothing.
- Scroll to the bottom of the menu (swipe up with a finger if needed).
- Tap Reset all and confirm with Reset.
Note that this resets the smoothing values as well as the pressure curve, so if you've tuned both, jot down your smoothing numbers first.
Why This Matters for Motion Work
If you're an animator, motion designer, or VFX artist, you probably aren't using Procreate as your primary tool, but it often shows up at the start or edges of a pipeline: storyboard frames, hand-drawn style frames, frame-by-frame effects animation, textured brush elements, or roto-style cleanup passes. In each case, inconsistent line weight and opacity cause real downstream problems.
- Frame-by-frame consistency: A pressure curve that responds predictably helps you hold line weight steady from frame to frame, which reduces boil you didn't intend.
- Alpha and opacity control: If strokes build opacity with pressure, a poorly tuned curve changes how much alpha detail lands in your exported layers, and that affects how they composite in After Effects or Nuke.
- Speed: When boarding or sketching dozens of frames, not fighting the tool saves meaningful time over a project.
Tune the curve once for your hand, test it on a short sequence of frames, and keep it stable through the job.
Taking Procreate Artwork Into a Motion Pipeline
Once your drawings feel right, the work is getting them into your compositor. Export flattened frames or layered elements as PNGs, name them with a consistent numbered sequence, and import them into After Effects, Premiere Pro, or Nuke as an image sequence. Keep a transparent background where you need to composite over footage or other elements.
Quick Reference
Final Tips
- Change one thing at a time and test with a real stroke, not a single dab.
- Make small moves to nodes; large swings are hard to reason about.
- Test with the brushes you'll use for the actual job.
- If problems persist after tuning, check the connection, the individual brush's pressure settings, and the stylus itself before blaming the curve.
A well-tuned pressure curve is a small change that makes every later step in your workflow more consistent, from the first sketch to the final composite.