How to Adjust Layer Transparency in Procreate
StyleFrame Team7 min read
To adjust layer transparency in Procreate, open the Layers panel, tap the letter next to the layer name (an "N" by default), and drag the Opacity slider beneath it. A faster route is to tap the layer with two fingers and slide left to reduce opacity or right to increase it. The slider method is non-destructive, so you can change the value as often as you like. The Adjustments > Opacity tool does the same job from the canvas.
Three Ways to Change Layer Opacity in Procreate
Procreate offers several ways to reach the same layer opacity value. They differ in speed, in how precisely you can read the number, and in whether the change can be revisited later.
Method 1: The Layer Opacity Slider
This is the most common route and the one to learn first.
- Tap the Layers icon (two overlapping squares) at the top right of the canvas.
- Find the layer you want to change.
- Tap the small letter to the right of the layer name. By default this is "N" for Normal blend mode.
- Drag the Opacity slider that appears beneath the blend mode list.
The percentage is shown as you drag, so you can land on a specific value like 40% or 65%. The same panel holds the blend mode list (Multiply, Screen, Overlay, and so on). If you are lowering opacity to get a particular look, check the blend mode at the same time, since the two interact.
Because the value lives on the layer, not in the pixels, you can reopen the slider at any point and set it back to 100%. Procreate's own documentation describes this as non-destructive.
Method 2: Two-Finger Tap and Slide
This is the quickest method once it is muscle memory.
- Open the Layers panel.
- Tap the target layer with two fingers at the same time.
- Slide a finger left on the canvas to make the layer more transparent, or right to make it more opaque.
This is useful when you are judging by eye, for example fading a sketch layer until it is just visible enough to trace over. It is less useful when you need an exact number, because finger sliding has less precision than the slider in Method 1.
Method 3: Adjustments > Opacity
The Adjustments menu (the magic wand icon at the top left) includes an Opacity tool that affects the active layer.
- Select the layer.
- Tap Adjustments > Opacity.
- Slide left or right anywhere on the canvas. The blue "Slide to adjust" bar at the top shows the value, starting at 100%.
- Use the buttons at the bottom to cancel, undo, redo, or reset.
- Tap the Adjustments icon again, or choose another tool, to commit.
This route is handy when you want undo and redo buttons while experimenting. It also explains the confusion in older forum threads, where users updated Procreate and could not find the old layer popover. The Adjustments menu and the two-finger tap were always alternatives to it. If you are following an old tutorial and the interface does not match, these two methods are the ones to try.
Adjusting Opacity on a Selection
Sometimes you only want part of a layer to become transparent. Procreate handles this with a selection, but the behavior is different from layer opacity.
- Open the Selection tool and make a selection using your preferred method (Automatic, Freehand, Rectangle, or Ellipse).
- Open the Layers panel.
- Tap the layer that contains the painted area with two fingers.
- Slide left on the canvas to reduce opacity, or right to increase it.
The important detail is that the change is applied when you leave this mode. That makes it a destructive edit: you can undo immediately, but you cannot return to the slider later and change the value. If you expect to revisit the transparency, avoid this approach. Put the area on its own layer instead (select, then copy and paste to a new layer, or cut to a new layer) and use the layer opacity slider, which stays editable.
Brush Opacity Is a Different Control
Layer opacity and brush opacity are easy to confuse. Brush opacity controls how transparent each stroke is as you paint. In the Procreate sidebar, the lower slider adjusts the opacity of the selected brush. Drag it up for more opacity and down for less.
Two things catch people out:
- Apple Pencil pressure. Many brushes respond to pressure, so if your opacity is set to maximum but strokes still look faint, the brush may be mapping light pressure to lower opacity. Check the brush's pressure settings.
- Stacking within a stroke. A low-opacity brush builds up with overlapping strokes, but layer opacity applies to the whole layer evenly. If you need a flat, uniform transparency over an entire shape, paint at full brush opacity and then reduce the layer opacity.
Non-Destructive vs Destructive: Which to Use
A simple rule keeps your files flexible:
- Use the layer opacity slider (Method 1) when the transparency is a design decision you may want to change.
- Use selection opacity only when you are committing to a one-off edit on part of a layer.
- Use the Adjustments > Opacity tool when you want a quick adjustment with undo and reset buttons, and you are happy to commit.
Layer-level transparency also combines well with other non-destructive tools in Procreate, such as clipping masks. A clipping layer above a base layer only paints within the base layer's shape, so you can lower its opacity without worrying about stray strokes.
What Happens to Opacity When You Export to Your Motion Pipeline
For professionals working in After Effects, Premiere Pro, Blender, Cinema 4D, or Nuke, Procreate is often a source of hand-drawn elements, textures, or style references. How transparency is exported matters more than how it is set.
- Layered files vs flattened files. Check how layer opacity and blend modes look after import, because results can differ between applications and between layered and flattened exports.
A practical tip: if you will animate fades in your compositing application, consider keeping elements at 100% opacity in Procreate and doing the fade there. Use Procreate's opacity for look decisions that should stay constant, like a translucent glaze or a faint pencil underlayer.
Troubleshooting Common Opacity Problems
I can't find the opacity slider. Make sure you are tapping the letter ("N") to the right of the layer name, not the checkbox. The checkbox toggles visibility.
The slider seems to do nothing. Confirm the correct layer is selected. A clipping mask layer or a group may be active instead of the layer you intended.
My strokes are too faint at 100% opacity. Look at brush settings and Apple Pencil pressure, not the layer opacity.
I changed a selection's opacity and now can't reverse it. That is the destructive behavior of selection opacity. Undo immediately if possible. Otherwise repaint or restore from an earlier state, and use a separate layer next time.
The opacity looks different after import. Check the blend mode in the receiving application, and confirm whether the file is flattened or layered.
Quick Reference
- Layer opacity: Layers > tap "N" > drag the slider.
- Fast adjustment: two-finger tap on the layer, slide left or right.
- Adjustments route: Adjustments > Opacity, slide, then commit.
- Part of a layer: make a selection, two-finger tap the layer, slide. This commits permanently.
- Brush opacity: lower slider in the sidebar.
Once you know which control changes the layer and which changes the stroke, opacity in Procreate stays predictable, and you can hand off clean, editable files to the rest of your motion pipeline.