How to Add White Border to Sticker Procreate
StyleFrame Team7 min read
To add a white border to a sticker in Procreate, duplicate your artwork layer, alpha lock it and fill it with white, then turn alpha lock off and apply a Gaussian blur. Next, use the Selection tool in Automatic mode and drag to set the border width, then fill that selection with white on a new layer beneath the artwork. Delete the blurred layer, and the sticker is ready to export as a transparent PNG.
Procreate has no native offset or stroke-around-shape command, so this blur-and-select workaround is a common approach. It's quick once it's muscle memory, and the same border can be reused for print-and-cut sheets, lettering, or sticker assets headed into a motion project.
What You Need Before You Start
- Procreate on iPad.
- Artwork on a transparent background. Either a layer you drew or a PNG you imported. The method relies on transparency, because the border is built from the shape of the pixels.
- A dark or colored background layer visible. A white border disappears against a white canvas, so hide the background layer or swap it for a dark color while you work.
- Artwork merged where needed. If your sticker is made of many layers, merge them into one first (or work on a duplicate of the project so the originals stay intact).
Step-by-Step: The Core White Border Method
1. Duplicate the artwork layer
Open the Layers panel, swipe left on the layer containing your sticker, and tap Duplicate. Make sure the duplicate sits below the original. If it doesn't, drag it down. Working on a copy means your original pixels never get blurred or recolored.
2. Alpha lock the duplicate and fill it with white
Set your active color to pure white. Tap the duplicate layer and choose Alpha Lock (or swipe right on the layer with two fingers). Then tap the layer again and choose Fill Layer. Because alpha lock restricts painting to existing pixels, only your artwork's shape turns white, leaving a clean white silhouette.
A quicker alternative some artists use is Adjustments → Hue, Saturation, Brightness, pushing brightness to 100% and saturation to 0. Either route gets you a pure white silhouette.
3. Turn off alpha lock and apply Gaussian Blur
Disable alpha lock, then open Adjustments (magic wand) → Gaussian Blur. Choose Layer mode and drag your pencil or finger to the right. Roughly 10–20% is a common range, but the right value depends on your canvas resolution and how thick you want the border.
The blur spreads the white silhouette outward past the edges of your artwork. That soft halo is what you'll convert into a hard-edged selection in the next step.
4. Make an automatic selection from the blurred layer
Tap the Selection tool (the S icon) and set it to Automatic. Tap on the blurred layer, then hold and drag your pencil left or right. This adjusts the selection threshold:
- Dragging right typically expands the selection and creates a thicker border.
- Dragging left tightens it for a finer border.
Release when the marching-ants edge sits where you want the outer border to land. If the selection grabs the empty background instead of the sticker shape, tap Invert.
5. Fill the selection on a new layer below your artwork
With the selection still active, create a new layer and drag it beneath your original artwork. Tap the layer and choose Fill Layer, with white as your active color. You now have a solid white shape that extends beyond your artwork on every side.
6. Delete the blurred layer
Hide or delete the blurred silhouette layer. What remains is your artwork on top, a clean white border layer beneath it, and a transparent background. Toggle a dark background on to check the result.
A Faster Variant for Whole Sticker Sheets
If you're bordering many stickers at once, merge the sticker sheet into a single layer, duplicate it, and run the same sequence on the whole sheet. One pass produces borders for every sticker at the same time.
Another time-saver: with Color Fill active and white set as your color, running the selection followed by Invert can fill the border automatically, which may let you skip a separate fill step. Test it on a copy of your file first, since behavior depends on which selection mode you used.
Fixing Common Problems
Bumpy or wobbly edges. The blur-and-threshold approach follows your artwork's edge, so soft brushes and low-opacity edges can produce uneven borders. Smooth them by tracing the outer edge with a hard-edged monoline brush in white on the border layer. This matters most if the file will go to a cutting machine, where a wobbly cut path creates wobbly cuts.
Gaps or holes inside the border. Letters with counters, thin fills, and sticker shapes with enclosed negative space can leave islands of transparency. Fill them by hand on the border layer, or increase the blur slightly so the white halo bridges the gap.
Border too thin or too thick. Go back to the selection step and drag the threshold rather than re-blurring. If you've changed canvas size, the same blur percentage will look different, so adjust to taste.
Border looks gray or semi-transparent at the edges. That usually means the selection threshold landed inside the blur's soft falloff. Push the threshold slightly wider, then fill again on a fresh layer.
White edge halo on dark backgrounds. Stray semi-transparent pixels from the original artwork can show as fringing. Tighten the selection a touch so the border sits cleanly outside the art.
Adding a Colored Border or Drop Shadow
The white isn't special. Fill the selection with any color and you get a matching colored outline. For a lifted look, duplicate the finished border layer, move it to the bottom, invert it to black, apply a Gaussian Blur, and lower its opacity. Offset it slightly for a more natural shadow. Keep the shadow on its own layer so you can toggle it before export.
Exporting the Finished Sticker
- Digital use: Hide the background layer and export as PNG to preserve transparency.
- Print and cut: Export a PNG at full resolution. Many cutters work from a separate cut-line, so you can also export the border layer alone as the path source.
Taking Procreate Stickers Into a Motion Pipeline
For motion designers and editors, a Procreate sticker is often just a starting asset. Sticker-style bordered elements are common in social video, lower thirds, and collage-style title sequences, and the white border is exactly what makes them read against busy footage.
Once the PNG is in After Effects, you have more control than Procreate gives you:
- Keep the border on its own layer so you can animate the artwork and border independently, or scale the border on a beat for a pop effect.
- Rebuild the border procedurally in your compositing software if you need it to stay consistent as the sticker moves or changes, without going back to the iPad.
- Export at generous resolution. Sticker art drawn at a small canvas size will soften when scaled up in a 4K comp, so draw large or upscale before compositing.
Quick Reference Checklist
- Duplicate the artwork layer and place the copy below.
- Alpha lock the copy and fill it with white.
- Turn off alpha lock and apply Gaussian Blur (about 10–20%).
- Use Selection → Automatic, and drag to set border width.
- Invert the selection if it grabbed the background.
- Create a new layer beneath the artwork and fill the selection with white.
- Delete the blurred layer and smooth edges with a hard brush if needed.
- Hide the background and export as a transparent PNG.
Once you've run through it a few times, the white border becomes a quick, repeatable step, whether the finished sticker ends up on a printed sheet or animated in a comp.