How to Add Straight Lines in Procreate
StyleFrame Team7 min read
Draw a stroke in Procreate and keep your Apple Pencil (or finger) on the screen at the end instead of lifting it. After about half a second the stroke snaps into a straight line, and touching a second finger to the screen locks the angle to 15° increments. The same hold gesture turns rough circles, rectangles, triangles, and multi-point outlines into clean QuickShapes. For straight lines on every stroke, switch on a Drawing Guide with Assisted Drawing.
Method 1: Draw a straight line with QuickLine
QuickLine is a fast way to get a straight line, and it needs no setup. With Paint or Erase selected and a layer active:
- Draw a rough line in the direction you want.
- Don't lift the Pencil at the end of the stroke. Hold still for a moment.
- The stroke straightens. While you're still holding, slide the Pencil to change the line's length and angle.
- Lift when it's where you want it.
Snap to clean angles
Once the line has snapped, touch a second finger anywhere on the canvas while the Pencil stays down. The line then locks to 15° increments, which makes true horizontals, verticals, and 45° diagonals easy. This is the gesture to use for hard-edged graphic layouts, title-safe guides, and perspective construction lines.
The line you get is a normal brush stroke, so it takes on whatever brush, size, and opacity you have selected. A monoline brush gives the cleanest, most vector-like result. Textured brushes keep their texture even on a perfectly straight path.
Method 2: Use QuickShape for geometric forms
QuickShape works with the same hold gesture, but you draw a closed or multi-segment form instead of a single line. Sketch a rough triangle, rectangle, circle, or custom polyline and hold at the end of the stroke. A notification appears at the top of the canvas and the shape regularizes.
Refine with a second finger
While the shape is still held, drag to change its size and rotation. Adding a second finger pushes it toward a regular form: a triangle becomes equilateral, a rough circle becomes a perfect circle, and a rough quadrilateral becomes a square.
Edit the shape after you lift
When you release, tap the Edit shape notification at the top of the screen. You can then:
- Switch the shape type, for example from a circle to a square.
- Drag transformation nodes to adjust individual points, which is useful for aligning the bottom edge of a mountain silhouette or making sure a polyline's start and end meet so it can be filled cleanly.
- Tap outside the shape to exit editing mode.
The edit menu is only available right after you create the shape. If you need to change it later, use the Transform options instead.
Method 3: Lock every stroke to a guide
QuickLine is great for single lines, but it's slow when you need dozens of precisely aligned strokes. Drawing Guides solve that.
- Open the Actions menu (wrench icon) and go to Canvas.
- Turn on Drawing Guide, then tap Edit Drawing Guide.
- Choose a guide type.
- Turn on Assisted Drawing in the guide settings.
With Assisted Drawing active, strokes are constrained to the guide, so you can scribble loosely and get lines that follow the grid or vanishing points. This is ideal for architectural environments, isometric UI or product scenes, and technical-looking graphics.
Two settings control where this behavior applies:
- Layer level: Tap a layer's thumbnail and use Drawing Assist to turn assistance on or off for that layer. Layers using it show an "Assisted" label.
- Input level: In Prefs > Gesture Controls > Assisted Drawing, you can enable assistance for the Apple Pencil or for touch.
Keep this in mind, because it explains a common complaint about straight lines in Procreate, covered next.
Troubleshooting: when Procreate only draws straight lines
Plenty of users hit the opposite problem: every stroke comes out straight, or only horizontal and vertical. Check these in order:
- Assisted Drawing for the Pencil. Go to Actions > Prefs > Gesture Controls > Assisted Drawing. If Apple Pencil (or Touch) is toggled on, turn it off. When a drawing guide has been set for a canvas, these toggles constrain your input to that guide, even if you've since switched the guide off.
- Drawing Assist on the layer. Open the Layers panel. If the layer thumbnail says "Assisted," tap it and switch off Drawing Assist.
- The canvas guide itself. Under Actions > Canvas, turn off Drawing Guide, or open Edit Drawing Guide and disable Assisted Drawing there.
- Stabilization settings. If strokes feel locked or over-smoothed and no QuickShape notification appears at the top, you're not seeing QuickShape. Check Prefs > Pressure and Smoothing, and use Reset if the sliders seem stuck. Also test a few different brushes, since stabilization can be baked into a brush's own settings.
- QuickShape timing. If lines snap when you don't want them to, or you want them to snap faster, go to Prefs > Gesture Controls and adjust the QuickShape delay, or turn the gesture off entirely.
If none of that helps, restart the app, and if the behavior began right after an update, record a short screen video before contacting Procreate support so they can see what's happening.
Tips for cleaner straight lines
- Work on a dedicated layer. Keep construction lines separate from finished art so you can hide or delete them later.
- Zoom in for endpoint accuracy. QuickLine follows where your Pencil lifts, so pinch in for precision when connecting two points.
- Use a monoline or hard-edged brush for geometry. Soft or textured brushes make straight lines look less crisp.
- Combine methods. Block in the perspective with a Drawing Guide, then use QuickLine for exceptions that don't follow the grid.
- Canvas size matters. If the lines will be scaled up in a video comp, start with a canvas large enough that edges don't soften later.
Getting straight-line work into a motion pipeline
If you're a motion designer or compositor, you're probably using Procreate for boards, style frames, or hand-drawn elements rather than finished art. A few habits make the handoff smoother.
Export for After Effects
- Export layered artwork as a PSD so each element, such as construction lines, shapes, and fills, stays on its own layer.
- Export a transparent PNG for single elements like a geometric overlay or a frame border.
- Keep straight-line layers named and ordered. Cleanly organized layers save time when you're parenting, masking, or animating in After Effects, Premiere Pro, or Nuke.
- If the lines need to scale significantly or animate as true strokes, consider rebuilding them as shape layers in After Effects, or in Cinema 4D or Blender if you're working in 3D. Procreate output is raster, so heavy scaling will soften edges.
Quick reference
Final thoughts
Straight lines in Procreate come down to three tools: hold-to-snap QuickLine for single strokes, QuickShape for geometric forms you can edit, and Drawing Guides with Assisted Drawing for consistent, grid-locked work. When something goes wrong, the culprit is often an assisted-drawing toggle, a layer setting, or a smoothing preference. Once your linework is clean, organize your layers, export in a format your compositor can use, and bring the drawing into your motion workflow.