How to Add Pressure Sensitivity in Procreate
StyleFrame Team7 min read
Procreate has no "add pressure sensitivity" switch. Pressure works automatically once a pressure-sensitive stylus, such as an Apple Pencil, is connected to a compatible iPad. To tune it, open Actions → Prefs → Pressure and Smoothing and reshape the pressure curve, then adjust individual brushes if only one feels off. If pressure isn't registering at all, the cause is usually the stylus, not a Procreate setting.
What Procreate Needs for Pressure Sensitivity
Pressure data comes from hardware. Procreate reads it from a connected smart stylus it supports. A generic rubber-tip or capacitive stylus works like a finger: it draws, but it never reports pressure or tilt. This is the most common reason artists think pressure is "missing."
Before changing any settings, confirm three things:
- You're using an Apple Pencil (or another stylus Procreate supports), not a basic touch pen.
- The stylus is connected to the iPad and charged.
- The brush you're testing is meant to respond to pressure. Some brushes ship with little or no pressure dynamics.
Step 1: Connect Your Apple Pencil
For an Apple Pencil 2nd generation or Pencil Pro:
- Swipe down from the top right of the iPad screen to open Control Center.
- Make sure Bluetooth is switched on.
- Attach the Pencil to the magnetic edge of the iPad and wait for the pairing dialog, which also shows the battery level.
Once connected, the Pencil should work in Procreate immediately. Draw a stroke with a default brush such as one from the Painting set, pressing lightly and then harder. If the line changes in size or opacity, pressure is working and you can move on to tuning it.
Step 2: Adjust the Global Pressure Curve
The global curve controls how the iPad's raw pressure input maps to the effect on every brush at once.
- Open a canvas (the menu is only available inside one).
- Tap the wrench icon to open Actions.
- Choose Prefs, then Pressure and Smoothing.
You'll see a graph. The horizontal axis is how hard you press, from none on the left to maximum on the right. The vertical axis is how strongly that pressure affects the brush, from no effect at the bottom to full effect at the top. The default is a straight diagonal line.
Making a brush respond faster
If a brush needs too much force to reach full opacity or size, tap the middle of the curve to add a node and pull it slightly upward. The same pressure now produces a stronger effect, so lighter strokes read more clearly. Move in small increments and test after each change.
Making a brush respond slower
If strokes jump to full thickness too easily, pull the middle node downward. You'll need to press harder to get the same result, which gives you finer control over light tones and thin lines.
Matching a tablet feel
Artists coming from a Wacom tablet often adjust the curve to approximate that response. A common approach is to nudge the bottom point of the curve to the right a little at a time until light pressure feels less twitchy. The right shape depends on your hand, so treat any preset advice as a starting point.
Procreate's own documentation advises against changing global pressure unless you need to, because the stock brushes are tuned for the default curve and a heavily modified curve can produce unexpected results. If you only need to fix one brush, use the per-brush settings instead.
Step 3: Set Pressure Behavior Per Brush
Global settings affect everything. Individual brush settings let you change how a single brush behaves.
- Tap a brush in the Brush Library to open its settings.
- Look for the controls that relate to pressure and size, and adjust them.
- Check settings such as size taper and softness, which can affect how the brush responds to pressure.
A few practical combinations:
- Expressive inking: a brush set up so light pressure gives a hairline and heavy pressure gives a bold stroke.
- Consistent line work: a brush set up so pressure barely changes thickness.
- Soft shading: a brush where pressure affects opacity, so you build values with gradual strokes.
Duplicate a brush before editing it. That way you keep the original and can compare the two directly.
Step 4: Add Smoothing and Stabilization
Pressure and stabilization often get tuned together. In the Pressure and Smoothing menu, the sliders at the top control stabilization applied across all brushes. Higher values smooth jitter, which helps with clean contour lines and long curves, but too much can make strokes feel laggy.
Troubleshooting Pressure Problems
Pressure only works in one direction
A common complaint is that line thickness increases as you press harder but won't get thinner when you lighten up mid-stroke. Check these in order:
- Disable size taper or softness on the brush. Taper settings can fight the live pressure response, and turning them off often makes the brush respond far more naturally.
- Review the pressure curve. If it's been bent, the response may be saturating early. Reset it and test again.
- Slow down. The iPad can struggle to match a desktop graphic tablet on very fast strokes, which can make pressure feel less precise.
No pressure at all
If every stroke is the same weight no matter how hard you press:
- Confirm you're not using a non-smart stylus or your finger.
- Check that the Pencil is paired and charged.
- Try a different brush, since some have pressure dynamics reduced or removed.
- Open Pressure and Smoothing and check that the curve hasn't been flattened.
You want pressure off
Sometimes you want uniform line weight. In Pressure and Smoothing, drag the top-right point of the curve to the top left, which makes the curve vertical. Brush thickness then depends only on the size slider, not on how hard you press. To go back, drag the point to the right or tap Reset all.
How to Reset Pressure Settings
If you've made too many adjustments and the brushes feel off:
- Go to Actions → Prefs → Pressure and Smoothing.
- Scroll to the bottom of the menu.
- Tap Reset all, then confirm with Reset.
This returns all settings in that menu to defaults, including stabilization, so note any values you want to keep first.
Using Procreate Artwork in a Motion Pipeline
Pressure-sensitive drawing in Procreate is useful beyond illustration. Many motion designers and animators use it to hand-draw style frames, storyboard panels, texture passes, and key poses that feed After Effects, Premiere Pro, Cinema 4D, Blender, or Nuke. Good pressure response means the line quality, ink weight, and shading you want are already in the art before it leaves the iPad.
That artwork can also serve as direction for AI-assisted motion work. is an AI video and motion tool built for artistic control rather than one-click output. Every generation is driven by reference images, video clips, and keyframes that you supply. For example, you could:
- Use hand-drawn Procreate frames as start and end keyframes in Frames-to-Video, so the motion travels between poses you drew.
- Use a Procreate painting as the style reference for Restyle or Ink-and-Paint, applying your line quality and palette to footage or renders.
- Take a flat illustration through 2D-to-3D or Turntable to explore a character or object from other angles, then use Remove Background to isolate it.
- Finish with 4K Upscale so the result holds up in a production timeline.
Iteration is non-destructive, so you can try variations without losing earlier versions. Output can be exported as image sequences, which drop into After Effects or Nuke for compositing, so your existing pipeline stays intact. An After Effects plugin is on the way. The control you build into your Procreate pressure settings carries forward, because the reference you draw is what directs the result.
Quick Reference
Final Tips
Change one thing at a time and test with the same stroke each time, such as a light-to-heavy-to-light line, so you can see what each adjustment does. Leave the global curve alone unless the default doesn't suit your hand, and do most of your shaping in individual brushes. If pressure seems missing, check the hardware first. Most "pressure sensitivity" problems in Procreate come down to the stylus, a bent curve, or a brush setting that was never meant to respond to pressure.